An insulated piston-cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. An electric resistance heater inside the cylinder is now turned on and 2200 kJ of energy is transferred to the system. a) Sketch a schematic diagram of the system and label all given information. b) Determine mass of the water, kg. c) Determine final enthalpy of the water, kJ/kg.

An insulated piston-cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. An electric resistance heater inside the cylinder is now turned on and 2200 kJ of energy is transferred to the system. a) Sketch a schematic diagram of the system and label all given information. b) Determine mass of the water, kg. c) Determine final enthalpy of the water, kJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. a) Define thermal efficiency and give one example of heat engine. b) The graph in Figure 1.1 shows one mole of monoatomic gas at initial temperature of 40 ˚C and volume 2 L expanding isobarically at a constant pressure of 2.5 × 105 Pa to 5 L. It is then cooled down at constant volume to a pressure of 1.2 × 105 Pa. The gas is finally compressed isothermally back to its initial state. Calculate i. the work done in process AB. ii. the amount of heat absorbed from A to B. iii. the work done by the gas from C to A. iv. the total work done in the complete process.
In a vertical piston cylinder arrangement, there is 300 kPa pressure and 2 kg of saturated liquid and saturated steam mixture water at 70% dryness in the cylinder. As a result of the heat transfer to the cylinder, the piston moves by increasing slowly at constant pressure and the heat transfer ends when the volume increases 2.5 times. a)Find the temperatures, specific volumes and specific internal energies in the initial and final states. b)Draw the P-v diagram of the process schematically, show the initial and final states on the diagram. c)Find the work done to the environment by the system during the process, kj d)Find the heat transfer, kj, to the system during the process.
1. The pressure in the substance drastically decrease from 354 to 21 POUNDS PER SQUARE INCHES (PSI), the heat energy of the open system reduces 555BTU/LB, and the volume increases from 1 to 10FT^3/LB. a.) Determine the work per LB. Units:BTU/LB b.) Determine the work in HP (Horse Power) for 10LB per min. (1HP = 42.4BTU/MIN) Units: HP
In a fixed volume tank, there is initially 0.8 kg of superheated water vapor at a temperature of 300°C and a pressure of 1 MPa. The final temperature drops to 120°C by drawing heat from the container and it is observed that the water has partially condensed. According to this; a) Volume of the tank b) Final state dryness x=?c) The amount of heat withdrawn from the tank as absolute value?
Inside a piston-cylinder device there is 5 kg of a moist water vapor at 125 kPa. At the beginning there are 2 kg of water in the liquid phase, and the rest is in the vapor phase. Then, heat is transferred to the water; the plunger, which rests on a set of stops, begins to rise when the pressure inside reaches 300 kPa. Heat transfer continues until the total volume increases by 20 percent. a) the start and final temperatures b) the mass of liquid water when the plunger starts to rise c) the work done during this process. Also plot the process on a P-v diagram
The piston-cylinder assembly, which initially contains 5 kg of water at 20 ° C and 400 kPA pressure, has a dryness level of 0.41 when it comes to the upper stoppers after the heat given at constant pressure. As the saturated steam is obtained after the heat given in constant volume; a)final pressure and temperature. b)Plot the state change on a p-v and t-v diagram. c)work done after the process and heat transfer
5. Steam with a specific volume 0.09596 m/kg undergoes a constant pressure process at 1.70 MPa until the specific volume becomes 0.13796 m'/kg. What are (a) the final temperature, (b) change in internal energy c) W d) Change in entropy and e) Q?
thermodynamics: rigid tank initially contains 1.5 lbm of air at 80 deg F and 50 psia. 25 BTU of heat is transferred to air. Determine the following: A) the final temperature of air B) the final pressure of air C) Change in enthalpy D) Change in entropy E) Change in internal energy
The diagram below represents a typical PV diagram: a) indicate the physical state of A b) indicate the physical state of B c) if the gas is initially at state A and goes to another state B, what process has it undergone? d) if the gas is initially at state B and goes to another state C, what process has it undergone? • C A To
A frictionless piston-cylinder assembly initially contains B m3 of air at A kPa pressure. In this state, a linear spring touches the piston but does not exert any force. Then the air is heated and the piston moves up. Finally, the volume is C m3 and the pressure is D kPa.a) Draw the state change PV diagram,b) Calculate the total work done by the air (kJ), c) Calculate the work done against the spring (kj).
Air treated as an ideal gas and having a specific heat at constant volume Cv-1200 J/kg.K undergoes a process. During this process, heat is observed to exit the system with an amount of 10 kJ while work is provided to the system with an amount of 22 kJ. If the initial temperature of air was 20 C, what is the final temperature of air if the mass of air undergoing the process is 0.4 Kg. Select one: a. 45 C b. 49.5 C c. 39.4 C d. 51.4 C
While the pressure remains constant at 700 kPa the volume of the system of hydrogen changes from 0.6 m3 to 0.2 m3. What are a) the change of internal energy, b) the change enthalpy, c) the change of entropy, d) heat and e) work for nonflow?