An FM signal is expressed as vpy (t) = 30cos 2710° t +3sin(2710ʻt)]. The deviationsensitivity is 2000r rad/s/V.a)b)c)d)what is the carrier frequency and modulating signal frequency ?what is the unmodulated carrier amplitude and modulation index ?find the frequency deviationobtain the equation for the modulating signalnimn bogn[30 kHz][30cos 2n10*t]

Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

An FM signal is expressed as vM (t) = 30cos 2710°t +3 sin(2710ʻt)]. The deviation sensitivity is 2000n rad/s/V. %3D 크) what is the carrier frequency and modulating signal frequency ? b) what is the unmodulated carrier amplitude and modulation index ? c) find the frequency deviation (p obtain the equation for the modulating signal [30 kHz] [30cos 2n10t]

An FM signal is expressed as vM (t) = 30cos 2710°t +3 sin(2710ʻt)]. The deviation sensitivity is 2000n rad/s/V. %3D 크) what is the carrier frequency and modulating signal frequency ? b) what is the unmodulated carrier amplitude and modulation index ? c) find the frequency deviation (p obtain the equation for the modulating signal [30 kHz] [30cos 2n10t]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 2 (a) Briefly explain the advantage of the following Amplitude Modulation (AM) type and state ONE (1) application for each AM type: i. Double Sideband Full Carrier (DSBFC) ii. Double Sideband Suppressed Carrier (DSBSC) iii. Single Sideband (SSB). (b) The AM waveform for the modulated signal is illustrated in Figure 1. i. Calculate the percentage of modulation index, m. ii. State the type of the modulated signal. Justify the answer. iii. Write the equation for the modulated signal. iv. Calculate the percentage of power efficiency. 3V -1IV Figure 1
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 10V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
You need a 20kHz sinusoid signal. What type of signal generator are you going to use? Discuss the setting of this signal generator to produce the required signal. You need an AM signal with 800kHz carrier frequency and 1kHz modulating signal. What laboratory equipment will you use? Describe the setting of the equipment to produce the required signal. The RF signal generator is used to produce an AM signal using an AF signal generator as the source of modulating signal. The RF generator is then connected to the oscilloscope. The oscilloscope displays an overmodulated AM signal. What adjustment would you do to produce an undistorted AM signal?
in FM , the maximum allowable frequency deviation is 4kHz and the frequency deviation by noise is 156.42HZ? then the signal to noise ratio is .......
i)Modulation process takes place in the modulator with two injection signals namely data orinformation and carrier. It is a vital step in generating a decent signal for electronic communication.Whenever the carrier is modulated by the information signal, new signals at different frequenciesare generated as part of the process. These new frequencies occur in the frequency spectrum withinthe range of the carrier frequency. Conclude these frequencies and mathematically explain itsgeneration with the help of diagrams. A) Upper sideband and lower broadbandB) Lower sidefloor and upperside floorC) Lower peak and upper peakD) Upper sideband and lower sidebandE) Lower bandwidth and upper gainF) All of the aboveG) None of the above
1. A modulating signal with an equation m cos2n(2k)t modulates a carrier signal with a peak amplitude of 9V and a frequency of 500 kHz. 5sin2n(3k)t + 6cos2n(6k)t + A. Calculate the RMS voltage of the modulating signal. B. Calculate the RMS voltage of the AM signal. C. Determine the bandwidth of the AM signal. D. Draw the frequency spectrum of the AM signal. Label completely.
4. Write down the general expressions of frequency modulated signal and phase modulated signal. And show the methods to generate FM signals.
Discuss how the circuit produces a Frequency Modulated Signal
An FM modulator has kf=30kHz/V and operates at a carrier frequency of 180 MHza. Find the output frequency for an instantaneous value of the modulating signal equal to150mV. b. If the carrier signal is modulated by a 2Vrms sine wave. Calculate the peak frequencydeviation.
2 (AM) A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with modulation index 0.8. What is the amplitude of the carrier? What is the power of the side bands? What is the efficiency of the modulated signal?
The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. If the peak voltage level of modulating and 1v and signal respectively, determine the modulating index. the carrier are 2V 2 1.5 1 0.5 -0.5 -1 -1.5 -2 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
A 10-MHz sinusoidal carrier wave of amplitude 1o mV is modulated by a 5 kHz sinusoidal audio signal wave of amplitude 6 mV. What is the modulation factor?