An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure.14 MPaUsing Mohr's circle, determine the principal stresses.MPa(f) ơ1 =|(g) 02 =MPа(h) Show all results on sketches of properly oriented elements.Choose the correct sketch.P14 MPа14 MPaА.PO, = 45*7 MPa7 MPaВ.P= 45 P14 MPa10 MPaC.P2= 45P10 MPa14 MPaD.= 45-Select- v

An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure. 14 MPа Using Mohr's circle, determine the principal stresses. MPa |MPa (f) ơ1 = (8) 02 = (h) Show all results on sketches of properly oriented elements. Choose the correct sketch. P 14 MPa 14 MPa A. P • = 45 Pa 7 MPa 7 MPa В. = 45

An element in pure shear is subjected to stresses Txy =-14 MPa , as shown in the figure. 14 MPа Using Mohr's circle, determine the principal stresses. MPa |MPa (f) ơ1 = (8) 02 = (h) Show all results on sketches of properly oriented elements. Choose the correct sketch. P 14 MPa 14 MPa A. P • = 45 Pa 7 MPa 7 MPa В. = 45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

: For the given state of stress, determine (a) the maximum principle stress (b) the maximum shearing stress (c) the angles Op and 0, (d) represent all results by Mohr's circle. ( P s (20)(7-5) 69 90 MPa 30 MPa 60 MPa t: -30 Oye.do 0x=90
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
! Required information Consider the given state of stress. to A16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise, using Mohr's circle. The normal stress ox'is ksi and oy'is |ksi. The shear stress Tx'y'is ksi.
3. The bar shown has a diameter of 2 in. and is made of an elastic-perfectly material with the stress-strain behavior as shown. If a force of P= 110 kip is applied to the bar, determine the stress in the segments AC and AB. o (ksi) P 20 |C B -2 ft - 3 ft e (in./in.) 0,001
Question-3 An element in pure shear is subjected to stresses - 16 MPa, as shown in the figure. Using Mohr's circle, determine (a) the stresses acting on an element oriented at a counterclockwise angle 0 = 20 from the x axis and (b) the principal stresses. Show all results on sketches of properly oriented elements. 16 MPa
The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to be εx = 217 x 10^6. Determine the applied load P. What is the shear strain γxy at point A?
Mohr's Circle normal and shearing stresses on the planes whose normals are at +60° 933. For the state of stress shown in Fig. P-933, determine and +150° with the X axis. Show these stresses on a sketch of the Ans. For 0 = 60°, o = 7.32 MPa and 1 = element. 10 MPa Y هم 20 MPa 10 MPa 20 MPa بنان +مروه قاعدين نفرا مقاومة ذكرى بیت مروة -X 10 MPa Flgure P-933. ١٥-٢٠١٠٠٥ البت
The stresses acting on element A in the web of a train rail are found to be ‘75 (MPa)’tension in the horizontal x-direction and ‘90 (MPa)’ compression in the verticaly-direction. Also, shear stresses of magnitude ‘40(MPa)’ act in the directions shown inthe figure.a) Draw Mohr’s circle for the state of stress.b) Determine the stresses (σx', σy' and τxy') acting on an element oriented at an angle‘D=-10 ˚’ from the horizontal. Show these stresses on a sketch of an elementoriented at this angle Note: If the angle D is positive, then the shear stress is in the direction shown onthe unit element figure; if it is a minus sign, then the shear stress is in theopposite direction shown on the unit element figure.
For the given state of stress of element A, strictly using Mohr's Circle perform the following: plane 1 plane 2 T-40 MPa plane 4 o=40 MPa 30° 1 plane 3 30° T=20√3 MPa 4 18.435° a) Draw its MOHRS circle b) Determine the principal stresses Op1= Op2= Op3= c) Determine the maximum shear stress Tmax= d) Determine the stresses on the horizontal & vertical planes OH= Ov= THV=
For certain values of w and P, the maximum positive bending moment in the beam is +7044 lb-ft, and the maximum negative bending moment is -8873 lb-ft. The cross section of the beam is shown. The pertinent section properties of the cross section are e = 2.90 in., f = 1.30 in., and I,= 18.3990 in.4. Calculate (a) the maximum tensile bending stress and (b) the maximum compressive bending stress that is produced in the beam. Enter your answers with the appropriate sign. B D b d y