Question 11An ammeter measures current in a circuit. The switch in the circuit is originally closed and the ammeter reads 2.3 A. When theswitch is opened, the reading on the ammeter (A) will(choose from below).a) be greater than 2.3 A.b) be less than 2.3 A.c) stay the same, 2.3 Ad) change in an unpredictable way.

Given circuit, Let the source voltage is V.

An ammeter measures current in a circuit. The switch in the circuit is originally closed and the ammeter reads 2.3 A. When th switch is opened, the reading on the ammeter (A) will (choose from below). a) be greater than 2.3 A. b) be less than 2.3 A. c) stay the same, 2.3 A d) change in an unpredictable way.

An ammeter measures current in a circuit. The switch in the circuit is originally closed and the ammeter reads 2.3 A. When th switch is opened, the reading on the ammeter (A) will (choose from below). a) be greater than 2.3 A. b) be less than 2.3 A. c) stay the same, 2.3 A d) change in an unpredictable way.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter3: Determining The Required Number Of Branch Circuits, Lighting Outlets, And Receptacle Outlets

Section: Chapter Questions

Problem 27R: The rating of a branch circuit is based on (Circle the correct answer.) a. the rating of the...

See similar textbooks

Similar questions

What will happen to the ammeter reading when switch S is closed? a) The reading will increase as compared to the reading when the switch is open b) The reading will be doubled as compared to the reading when the switch is open c) The reading will decrease as compared to the reading when the switch is open d) The reading will remains the same as compared to the reading when the switch is open
When you connect a voltmeter to read a dc voltage a. polarity is not important b. connect the voltmeter in series with the circuit c. connect the voltmeter across the component d. connect the common meter lead to the most positive point in the circuit
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
True or False: Ohms law applies to all types of electrical circuits.
Question 9 An analog voltmeter has 100 divisions on the scale. The voltage read is 6 volts and the meter has two ranges as 0 – 10 volts and 0-100 volts. Find the uncertainty in the measured value in both ranges. (Uncertainty = ±½ VFSD / # of divisions) Question 10 The following values obtained from the measurements of the values of 147.2,147.4,4,147.9,148.1,147.7,147.5,147.6,147.4,147.6 and 147.5. Calculate: The arithmetic mean The standard deviation
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本
For the circuit in Figure 73 the meter reads 7.84 mA when the switch is in position A.(a) What is the resistance of ?(b) What should be the meter reading for switch positions and D?(c) Will a 1⁄4 A fuse blow in any position of the switch?
(1.11) In roder to run a specific electric vehicle using de mior dove in a proper way, one of the following chopper drive circuit can be used a) Class-D de motor drive b) Class-E de motor deve d) Class C de motor drive e) A + B B + D None of the above.
Two 115-V incandescent lamps A & B are connected in series across 230-V de source. Lamp A is rated 100 W and lamp B is rated 60 W. Which lamp is abnormally bright and hence will burn out soon? a) Lamp A b) Lamp B c) Both lamps will be abnormally bright d) Both lamps will work normally
Fill in the box the correct flow of the process of generation of electrical energy in the pwer plant
If you tested the system with a scan tool and you observed a diagnostic trouble codes DTC P0503 what would that indicate
We want to measure the amount of current flowing to an old light bulb. We expect that the result will be around 5A. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SUDE SWITCH: LEFT- OFF MIDDLE- DCVOLTS DC mA NUMERICAL VALUE OF VOLTS OR mA OR OHMS DISPLAYED HERE 0.00 OHMS RIGHT - AC VOLTS AC mA OFFOD AC DC-A DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 200 (SELECT RANGE) 2K. 20K. •200 20u MOVE ROTARY SWITCH TO THIS AREA TOo READ mA (SELECT RANGE) 200K 20u *200u m 2M 20M 200m 20m 10A COM vn PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin. NOT CONNECTED