An ammeter (instrument that measures current) carries 0.05 A and is in parallel with a shunt resistor drawing 1.9 A. If the voltage across the combination is 4.2 V, find (a) the total current, (b) resistance of the shunt, (c) resistance of the ammeter, and (d) total resistance. = 1.9 A 4 = 0.05 A %3! V = 4.2 V Shunt resistor Ammeter resistance

An ammeter (instrument that measures current) carries 0.05 A and is in parallel with a shunt resistor drawing 1.9 A. If the voltage across the combination is 4.2 V, find (a) the total current, (b) resistance of the shunt, (c) resistance of the ammeter, and (d) total resistance. = 1.9 A 4 = 0.05 A %3! V = 4.2 V Shunt resistor Ammeter resistance

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B- What is the Between AM-DSB and Q2) find the signal at each indicating point of figure 1. (0.3-3.4) KHZ BPF LSB S вре USB 10 Cos (5x181Tt) v 6 8 Cos (2184)V AM-DSB/SC
RG C1 Vin H VDD = 1.8 V RD HEM₁ mA Determine the operating drain current. Answer: ID= C2 HH Given: VDD = 1.8 V, RG = 50 kOhm, RD = 2 kOhm, W/L = 20 um/um, VTO = 0.50 V, KP = 250 uA/V², LAMBDA = 0.20 V-1, GAMMA = 0, PHI = 0.70 Find: - Vout
For a simple resistive potential divider, the CRO rating of oscilloscope is 250 V. For the amplification ratio in the range 1050-1175, what will be the range of V1 values that can be measured with this instrument? What will be the range of resistor ratio value R1/R2
2.a Determine the output voltage for the circuit (a) for each input voltage in (b), (c), and (d). Via Vin R1 +25 v +12 V +5 V 4.7 ko Vin Vout 0- 0- R2 4.7 kN –25 V -12 V -5 V (a) (b) (c) (d) Indicate the peak values (up to 2 significant decimal places) during the positive and negative half cycles. No need to indicate the sign. (b) positive half cycle peak Vout = + V negative half cycle peak Vout = - V (c) positive half cycle peak Vout = + V negative half cycle peak Vout = - V (d) positive half cycle peak Vout = + V negative half cycle peak Vout = - V
4. For the circuit given in Figure 3, determine Ig, Ic, Vg, VE, and VCE- Vcc=10V R1 220ka Rc 4.7kQ B= 300 VBE(on)=0.7V R2 51ka RE 1.2kQ Figure 3. Voltage divider biasing circuit.
For the circuit below and V1 waveform shown, plot Vout: U1 Vout OUT R1 OPAMP 1M V1 C5 20u Input voltage to circuit 15 12 6. 10 15 20 25 Time (msec) V1 (volts) 5/
3-phase transfomer configuration in figure imagen: Ammeter A4 is measuring_______, Ammerter A5 is measuring_____, Ammerter A6 is measuring___, Voltmeter V1 is measuring_____, voltmeter V2 is measuring____, Voltmeter V3 is measuring ______, Voltmeter V4 is measuring_____,Voltmeter V5 is measuring______. A- line voltage B-phase voltage C- meither "a" nor "b" d- both "a" and "b"
Q1: Verify the mode of operation with justification and draw the load line for each transistor shown below: +5 V RE B-80 Rg 1 k2 Ca Rc=10 k Rg= 20 kQ o Vc Rg= 10 k2 Rc= 6.5 kQ RL= B-75 VEE= 20 V Vcc= -25 V + Rg=2 kQ ww-
Figure 4 b) Figure 5 shows the silicon base BJT with a Rc = 1 kQ, Rg = 10 k2, Vcc = 11 V, VBB = 6 V, BDC = 99. Determine Ig, Ic, lE, VCE and VCB- Rc 1 ko Vc 10 kn 11 V VBB 6 V Figure 5
Answer the following Questions referring the circuit in figure 10. Determine, a) VD b) VR and c) ID ID E8V + VD- Si IR R22.2 k2 VR Figure 10
6) A step input of 5 A is applied to an ammeter. The pointer swings to a voltage of 5.18 A and finally comes to rest at 5.02 A. (a) Determine the overshoot of the reading in ampere and in percentage of final reading. (b) Determine the percentage error in the instrument.
(a) = 56kΩ, R2 Given the voltage-divider bias configuration of Figure 2. Assume R₁ 8.2k, Rc = 6.8k, Rɛ = 1.5kQ, ß = 90, and Vcc=22V. Determine, the base current, IB, the collector current, Ic, the voltage between collector and emitter, VCE, the voltage at collector, Vc, he voltage at emitter, VE, and the voltage at base, VB. Vs Rs www + Zi R₁ C₁ R2 www ww +12V Rc RE www Figure 2 CE C₂ RL Zo ww Vo