A bronze bar is fastened between a steel bar and analuminum bar as shown in the figure. Axial loads areapplied at the positions indicated. The allowable overalldeformation is not to exceed 1.2 mm. Assume that the2PAluminumL- 1.5 mA= 550 mmE= 70 GPaSteelBronzeL= 2.0 mL= 1.0 mA= 600 mmA= 650 mmE= 200 GPaE= 83 GPaassembly is suitably braced to prevent buckling. Find themaximum permissible value of P.

To find maximum permissible value of load P

aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. The allowable overall Aluminum Steel L 1.0 m A 600 mm Bronze L- 2.0 m A 650 mm L 1.5 m deformation is not to exceed 1.2 mm. Assume that the A= 550 mm E- 200 GPa E- 83 GPa E= 70 GPa assembly is suitably braced to prevent buckling. Find the maximum permissible value of P.

aluminum bar as shown in the figure. Axial loads are applied at the positions indicated. The allowable overall Aluminum Steel L 1.0 m A 600 mm Bronze L- 2.0 m A 650 mm L 1.5 m deformation is not to exceed 1.2 mm. Assume that the A= 550 mm E- 200 GPa E- 83 GPa E= 70 GPa assembly is suitably braced to prevent buckling. Find the maximum permissible value of P.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber= 20MPa Allowable shear strength of the steel = 200MPa Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt?
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
hexagonnal head 30 60 mm threads bolt diameter @ threads 32 min %3D bolt diameter = 38 mm T=80 kN 1. Calculate the tensile stress in the body of the bolt. 2. Find the tensile stress at the root of the threads. 3. Find the compressive stress at the head as the bolt bears on the surface to resist tensile load.
Required information A square yellow-brass bar must not stretch more than 2.4 mm when it is subjected to a tensile load of 34 kN. Given: E= 105 GPa and that the allowable tensile strength is 104 MPa, determine (a) The allowable side length of the cross-section (b) is the allowable value a maximum or a minimum? Why? (c) The allowable length of the bar (d) is the allowable length a maximum or a minimum? (a&b) The allowable side length, for the square cross section, is given as [ (mm) and the value is a (Click to select)
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
Brass. (c). A bar of length 1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter being 10 mm as shown below. Under a load of 30 kN, if the extension of the bar is 0.222 mm, what is the modulus of elasticity of the bar? mam um
d Given: 9/8 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731 inch Inside diameter of washer = 9/8 inch Tensile stress in the nut = 18 ksi Bearing stress = 800 psi 2 in Required: 5/8 in Shearing stress in the head of the bolt Shearing stress in threads of the bolt Outside diameter of the washer 1 2. 3. 0.731 7/8
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to aodal loads as shown. If P-7 IN, Determine the total aodal deformation (in mm). Indicate negative sign f comoression. @ 5P O 3P E-200 6P 30 mm emm 80 mm 30 mn 30 mm
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 25 mm= DIAMETER OF BOLTS 45 45mm fmmy C. 90mm 90mm 90mm Comm P
* TRUTT 50 kN/m 8m TIZI SLAB THICKNESS 150mm 2500 mm fe'= 21 MPa fy = 414 тра Cc = 40mm spacer barp=25mm Say bw= 0.6h DESIGN THE T-BEAM AND SHOW THAT TENSION STEEL YIELDS AND THE BEAM IS TENSION CONTROLLED