B8 Alm long, 5 cm outer diameter copper pipe with surface threads acting as fins carries hot oil at110°C. Each fin length is 1 mm with a thickness of I mm to0, with a pitch (fin distance) of 1 mm.If the ambient temperature is 30°C, calculate the heat transfer out of the finned area of the pipe.Use the figure for assistance. Take the convective heat transfer coefficient as 50 W/m?."C.LImP-1 mm14-1 mmD=5 cm-I mm

Given: length of the pipe=1m outer diameter of the pipe→D=5cm=50mm length of the fin→L=1mm thickness…

Al m long, 5 cm outer diameter copper pipe with surface threads acting as fins carries hot oil at 110°C. Each fin length is 1 mm with a thickness of I mm too, with a pitch (fin distance) of I mm. If the ambient temperature is 30°C, calculate the heat transfer out of the finned area of the pipe. Use the figure for assistance. Take the convective heat transfer coefficient as 50 W/m2."C. LIm P-1 mm 14-1 mm D-5 em 1-1 mm

Al m long, 5 cm outer diameter copper pipe with surface threads acting as fins carries hot oil at 110°C. Each fin length is 1 mm with a thickness of I mm too, with a pitch (fin distance) of I mm. If the ambient temperature is 30°C, calculate the heat transfer out of the finned area of the pipe. Use the figure for assistance. Take the convective heat transfer coefficient as 50 W/m2."C. LIm P-1 mm 14-1 mm D-5 em 1-1 mm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.62P

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, inside diameter of Di 1 50 W/m-K) has an = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of = 250 mm and wall thickness to = t¡. Determine the maximum allowable crude oil temperature to ensure the Di, 2 polyurethane foam insulation (kp temperature of T, 0.0675 W/m-K) between the two pipes does not exceed its maximum service = 70°C. The ocean water is at T o, 0 = -5°C and provides an external convection heat transfer р, таx coefficient of ho = 500 W/m2.K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m2-K. (2) It is proposed to enhance the performance of…
Q3. A Jem diameter tube has eircumferential fins of rectangular profile. The fins are costructad of aluminum and are 2mm thick and 20 mm long. The tube wall temperature is maintained at 250°C, and the environment temperature is 50 °C. The heat-transfer cocfficient is 180 W/m' C. Determine the number of fins per meter of length of the tube that increase the heat loss from the tube by 400% of that without fins, (fin effectiveness=4).
Q. IsTeam at 605 K Flow in Alpipe with thermal conductivity K-188 W/m. c whose in and out diamter D₁ = 2 inche and D₂=58mm respectively. The pipe is covered with Tuto insulation material First was glass wooL K=0,06 and second cuas insulation K=0,01 w/m.c FirsT 33mm and second 13 mm, Heat is Lost to the surrounding at Too' Too2=288K by natural convection and radiation, with combined Theat Transfer coefficent of h=22,8 W/m² C, Taking heat Transfor coefficent inside pipe To be hi-48.9 W/m². C. Find Heat loss por length and Temp. dropp. ??
A steam pipe of length Imeter is passed through a room in which air and wall temperature is at 30°C while surface temperature of the pipe is 400°C. If the diameter of the pipe is 40mm and average heat transfer coefficient 20W / m°C, then what is the rate of heat loss(kW) from the pipe?
ать Tb=250°C 8mm 120mm -L=S = 50mm K-300 W mk h=160W/m²K Too = 32°C Tmm nfin= ? Determine the temperature distrubition of the fin shown in figuere. Tip of the fin is adiabatic Continuous Accept it as an one-dimensional heat transfer. in a regime for the thin-tip air foil with the Shape shown in figure.
An aluminum pipe has a length of 75 m at atemperature of 18°C. An adjacent steel pipe at thesame temperature is 5 mm longer than thealuminum pipe. At what temperature (C) will thealuminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients ofthermal expansion of aluminum and steel are a = 23 x 10–6/°C and s = 12 x 10–6/°C,respectively.)
To cool the hot oil, an engineer has suggested that the oil be pumped through a pipe submerged in a nearby lake. The pipe (external diameter = 20 cm) will be placed in the horizontal direction. The temperature of the outer surface of the pipe averages 130 ° C. The surrounding water temperature is assumed to be constant at 10 ° C. Pipe length 100 m. If it is assumed that there is no water movement. a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. = Answer Watt / (m² ° C) b. Determine the heat transfer rate from the pipe to the water. = Answer kW
To cool the hot oil, an engineer has suggested that the oil be pumped through a submerged pipe in a nearby lake. The pipe (external diameter = 20 cm) will be placed in the horizontal direction. The average pipe outer surface temperature is 130 °C. The temperature of the surrounding water is assumed to be constant at 10 °C. Pipe length 150 m. If it is assumed that there is no movement of water. a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. =AnswerWatts/ (m² °C) b. Determine the rate of heat transfer from the pipe to the water. =AnswerkW
Q3- A 7cm diameter tube has circumferential fins of rectangular profile. The fins are constructed of aluminum and are 2 mm thick , 8 mm long and are spaced 12 mm apart. The tube wall temperature is maintained at 200 C, and the environment temperature is 25 C. The heat-transfer coefficient is 150 W/m2 C. (1) determine the number of fins per meter of length of the tube. (2) calculate the total heat loss from the fins.
Hot water at 160 ⁰C is passing through a pipe, and it is lagged with a plastic covering. The coefficient of thermal conduction of the plastic is 0.2 Wm-1K-1 and the heat transfer coefficient is 16 Wm-2K-1. The ambient temperature surrounding the pipe is 25 ⁰C. Determine the critical radius and hence the maximum heat loss. Calculate the heat loss for varying thicknesses of lagging and plot this against the thickness. From the graph, estimate an optimal thickness of lagging and explain your reasons. You can use Excel for the calculations and plotting.