ain how communication occurs across a local Ethernet network? You must include detail on the Ethernet standard. Ethernet, Internet Protocol & Transport Protocols is deliberately broken down into a sensible order to use for tasks 14 and 15. Remember, Ethernet operates over the bottom two layers of the OSI model: Data link layer Frames CSMA/CD

ain how communication occurs across a local Ethernet network? You must include detail on the Ethernet standard. Ethernet, Internet Protocol & Transport Protocols is deliberately broken down into a sensible order to use for tasks 14 and 15. Remember, Ethernet operates over the bottom two layers of the OSI model: Data link layer Frames CSMA/CD

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 9VE

See similar textbooks

Similar questions

There are three layers in the hierarchical design of Ethernet networks.With the aid of a diagram, briefly explain these layers?
There are three layers in the hierarchical design of Ethernet networks. With the aid of a diagram, briefly explain these layers.
Computer Science A 10-Mb/s Classic Ethernet transmits data packets obtained from the Network Layer. Assume for simplicity that the obtained data packets are directly placed into the MAC Ethernet frame, i.e. that no extra bytes are added in the LLC sub-layer.
Design an Ethernet network to connect a single client PC to a single server. Both the client and the server will connect to their respective workgroup switches via UTP. Their workgroup switches are connected directly by a trunk link. The two switches are 900 meters apart. They need to communicate at 800 Mbps. Your design will specify the locations of any switches and the transmission link between the switches. Then add another client next to the first client. This client will also communicate with the server and will also need 800 Mbps in transmission speed. Again, your design will specify the locations of switches and the transmission link between the switches.
Explain, using words and a time diagram, why ethernet (IEE 802.3) has a minimum frame size. How would the minimum frame size change if the maximum network doubled?
Discuss any two constraints of computer networks based on shared media with the aid of suitable illustrations.Are there any differences between half duplex traditional Ethernet, half duplex fast Ethernet, and half duplex gigabit Ethernet in terms of slot time and maximum network diameter? Explain!If a company has a single Fast Ethernet hub, it may divide its network into three Fast Ethernet hubs linked by one Fast Ethernet switch to form a Fast Ethernet LAN. Are split networks more efficient than their original counterparts? With the aid of a suitable diagram, explain.
Efficiency Principle:Ethernet V1 access protocol was designed to run at 10 Mbps over 2.5 Km using 1500 Byte packets. This same protocol needs to be used at 100 Mbps at the same efficiency (utilization). What distance can it cover if the frame size is not changed? (Note: be careful with the units.
Why Frame Relay was originally designed for use across Integrated Services Digital Network (ISDN) interfaces? A connectionless protocol, such as Ethernet, defines the route of a packet through source and destination addresses. However, a connection-oriented protocol, such as ATM, defines the route of a cell through virtual connection identifiers (VPIs and VCIs). Could you explain this statement?
A connectionless protocol, such as Ethernet, defines the route of a packet through source and destination addresses. However, a connection-oriented protocol, such as ATM, defines the route of a cell through virtual connection identifiers (VPIs and VCIs). Could you explain this statement?
2. Ethernet frames must be at least 64 bytes long to ensure that the transmitter is still going in the event of a collision at the far end of the cable. Fast Ethernet has the same 64-byte minimum frame size but can get the bits out ten times faster. How is it possi- ble to maintain the same minimum frame size?
please answer (a) and (b) completely. Thanks a lot Consider a 10Mbps Ethernet network consisting of 20 nodes interconnected by a bus topology with a single bridge placed in the approximate center of the network resulting in an equal number of nodes on each side of the bridge. Briefly explain why collisions can/cannot occur. If two pairs of nodes attempted to communicate at the same time, discuss the throughput they can achieve.
Assume there is a shared connection with a 1 Mbps speed, such as an Ethernet bus. How long (in microseconds) does it take to deliver a frame with a 1000 bit length over this link?