ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the reactions at supports b. Draw Shear and Moment Diagrams C. Compute for deflection at A (AA) and slope at C (ec) using Conjugate Beam Method 50 kN 90 kN B ↓ A C ||---6m 9 m El = constant E = 70 GPa I = 95 (106) mm4 -9 m

ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the reactions at supports b. Draw Shear and Moment Diagrams C. Compute for deflection at A (AA) and slope at C (ec) using Conjugate Beam Method 50 kN 90 kN B ↓ A C ||---6m 9 m El = constant E = 70 GPa I = 95 (106) mm4 -9 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm; link CD is-made of steet E = 200 GPa) and has a cross-sectional area 600 mm. For the 30-kN force shown, determine the deflection (a) of B, (b) of D, (c) of E. 0.4 m 0.3 m 30 kN E T0.4 m 0.2 m
For the beam shown, how does the shear change as you move from A to B? L- Select the correct response: There is not enough information to tell. It stays constant. It decreases linearly. It increases linearly
In the restrained beam shown, solve for the following a. end moments b. max deflection 15KN im
B.2. Elementary beam theory predicts that the axial bending stress ox in a prismatic beam is given by: σ, X (M.1, M,1,)y+ (M, I. - M.1,-) z (1,1.-1²-) where My and M₂ are bending moments applied to a cross-section, and where ly, Iz and lyz are second moments of area in the usual notation (Oxyz is a Cartesian coordinate system in which the x axis corresponds to the centroidal axis of the beam). (i) What assumptions have been made in the derivation of the above expression? (ii) Indicate by means of a sketch the directions in which positive values of the bending moments My and M₂ act on a cut plane facing in the positive x direction.
Solve for the reactions, the deflection at free-end, and the slope at the midspan. Use E = 200 GPa and I = 50 x 106 mm4 Final Equations with value of C1 and C2 EIy'' = EIy' = EIy = RA: RB: RC: Deflection: Slope:
Problem III. From the given fixed beam at both ends, solve the following questions using constant EI. a. Reactions at A b. Reactions at B c. Slope at 6m from B in radians d. Displacement at 4m from A in mm 4kN/m 4m -6m 12kN/m
Solve for the reactions, the midspan deflection, and the slope at the midspan. Use E = 70 GPa and I = 100 x 106 mm4 Final Equations with value of C1 and C2 EIy'' = EIy' = EIy = RA: RB: MA: Deflection: Slope:
ACTIVITY 5- Truss Analysis Analyze the loaded truss as shown. Be guided as follows: a. Solve for the reactions at supports b. Solve for all member forces by method of joints and method of sections c. Compute for horizontal and vertical deflection at B (ABH and ABv) using Virtual Work Method 35 kN- EA = constant E = 200 GPa A = 1,200 mm2 4m A B 84 kN 4m 3m
QUESTION 03 A beam ABCD is supported and loaded as shown in Figure Q3. The flexural rigidity, El is constant. By using Macaulay's method, and take point A as origin, determine the: (a) Reactions at all supports A, C and D. (b) Deflection at point B (c) Slope at support A 1 m 1 m 1 m 2 kN/m 4 kNm Figure Q3/ Rajah S3
9.3-17 The beam shown in the figure has a guided suppot at A and a roller support at B. The guided support permits vertical movement but no rotation. Derive the equation of the deflec- tion curve and determine the deflection ô, at end A and also dc at point C due to the uniform load of intensity q PIL applied over segment CB and load P at x = L/3. (Note: Use the second order differential equation of the deflection curve.)
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m H Figure 1: Overhang beam L C Find the maximum absolute value of the deflection between the supports A and B - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
Before the load P was applied, a gap, 8, existed between the cantilever beam AC and the support at B. Knowing that E=200 GPa, determine the magnitude of P for which the deflection at C is 8 and the reaction at B P A В C 60 mm og. 60 mm 0.5 m -0.2 m→| S0=1.25mm,S=2.5mm