A W14 x 90 steel beam of A992 steel (Fy= 350 MPa and Fu= 450 MPa) supports a uniformly distributed gravity service load of 70 KN/m (60%DL and 40%LL) on a simple span of 7.5 m. The 60% gravity service dead load includes the weight of the beam. Lateral bracing is provided only at the ends and at the third points between supports. The loads are applied thru the shear center. Use ASD -WHx90 7.5m section Determine the value of Cb for the beam.0

A W14 x 90 steel beam of A992 steel (Fy= 350 MPa and Fu= 450 MPa) supports a uniformly distributed gravity service load of 70 KN/m (60%DL and 40%LL) on a simple span of 7.5 m. The 60% gravity service dead load includes the weight of the beam. Lateral bracing is provided only at the ends and at the third points between supports. The loads are applied thru the shear center. Use ASD -WHx90 7.5m section Determine the value of Cb for the beam.0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete one slab is built integrally surrounding with its supports (beam size is 200mm x 400mm) and consist of three spans, each with a clear span of 3.6m (exterior end), 3.4m (interior span) and 3.6m (exterior end) respectively. Design the Middle Span. LOADS: Ceiling = 0.35 kPa Flr Fin = 1.2 kPa Elec = 0.15 kPa Selfweight not yet included Live Load = 2.30 kPa PARAMETERS: Yconc = 23.6 kN/m3 fc = 21 MPa fy = 420 MPa; fytemp = 276 MPa Main bars dia = 12mm Temp bars, dia = 10mm Determine the Maximum Negative Moment at the Middle Span (kN- m) NOTE: Don't Consider the Live Load Pattern Loadings
A truck and trailer combination crossing a 10m simply supported span has axle loads of 0.8X, Y, and Z/3 separated respectively by distance of 1.5 m and 3.5 m. Design the beam in shear and bending (LRFD). Hint: The axle loads below are moving loads. Neglect the self-weight of the beam. Use W-shape A992 steel. 264 kN 189 kN 308 kN 1.5 m 3.5 m 10 m-
A welded plate girder of 18 m span having flange plates 400x16 mm for each flange and 200x10 mm web. Compute the sectional properties and moment of resistance of the plate girder . Design also the end bearing and intermediate transverse stiffener, if the girder is subjected to U.D.L. of 120 kN/m
Design a welded plate girder for simply supported bridge deck bear with a clear span of 20m, subjected to the following: Dead load = 18 kN/m,Impesed load = 8 kN/m, Two moving loads = 140 kN each spaced 2.5 m apart.Assume that top compression flange of the plate girder is restrained laterally and preventedfrom rotating. Use Ex- 250 MPa. Design as an unstiffened plate girder with thin webs.
Strength Of Materials Answer should be 45 kN/m; 0.26 cm :) A compound girder consists of a 45 cm by 18 cm steel joist, of weight 1000 N/m, with a steel plate 25 cm by 3 cm welded to each flange. If the ends are simply-supported and the effective span is 10 m, what is the maximum uniformly distributed load which can be supported by the girder? What weld thicknesses are required to support this load? Allowable longitudinal stress in plates = 110 MN/m2 Allowable shearing stress in welds = 60 MN/m2 Allowable shearing stress in web of girder = 75 MN/m2
A prismatic beam having 275mm x 500 mm is reinforced for flexure at the bottom with 5- phi 20 mm with an effective deapth of 420mm. It is simply supported over a clear span of 6m and designed to support a total factored uniformly distributed load of 36kn/m over the entire span. Concrete weighs 24kn/^3, concrete streangth f'c = 21 mpa and rebar strength fy= 280 mpa. Determine the required nominal shear force the stirrups must sustain based on the critical shear force at a section located distance "d" from the face of the supporta. 24.2b. 32.2c. 28.4d. 15.3
Q5: Answer Only One A precast T beam is to be used as a bridge over a small roadway. Concrete dimensions are bw= 400 mm, hf 125 mm, and h= 750 mm. The effective depth d= 600 mm. Concrete and steel strengths are f 'c= 38 MPa and fy = 420 MPa, respectively. Determine the design moment capacity of the girder. The beam is used on a 5 m simple span. A) b = 1300 mm B) b = 1200 mm %3D %3D %3D %3D %3D
A welded plate girder of Grade S275 steel carries two concentrated loads transmitted from 254x254 UC 107 columns at the third points. The columns rest on the top flange and the loads are each 400 kN dead load and 250 kN imposed load, respectively. The plate girder is 12 m span and is simply supported at its ends. The compression flange has adequate lateral restraint at the points of concentrated loads and at the supports. Assume that the weight of the girder is 4 kN/m and that the girder is supported on brackets at each end. Assuming that the depth limit is 1400 mm for the plate girder, (a) draw the shear force diagram; (b) draw the bending moment diagram, (c) estimate the optimum depth for the plate girder; (d) calculate the flange area. Assume that the flange plates are less than 16mm for a steel grade of 275 N/mm2.
A rectangular beam for a 6 m simple span to support a uniform dead load of 15 kN/m and live load acting at midspan of magnitude 90kN. fc’=21 MPa, fy = 350 MPa, Wc=24.56 kN/cu.m, b = 350mm, assumed steel ratio is 45% of the balanced steel ratio, if the assumed weight of the beam is 23% of the total load, _____pieces of 25-mm bars are to be used.
A reinforced concrete beam is 400mm wide and with an effective depth of 530mm. It has a tensile reinforcement of 4-25mmo, fc' = 21 MPa and fs = 124 MPa. Calculate the total safe uniform load the beam could support over a simple span of 6m in kN/m.
A prismatic beam having 275 mnn x 500 mm is reinforced for flexure at the bottom with 5-020 mm with an effective depth of 420 mm. It is simply supported over a clear span of 6 m and designed to support a total factored uniformly distributed load of 35 kN/m over the entire span. Concrete weighs 24 kN/m, Concrete strength f'c - 21 MPa and rebar strength fy - 280 MPa. Determine the required nominal shear force the stirrups must sustain based on the critical shear force at a section located distance "d" from face of support. OA 32.2 O B. 24.2 OC.28.4 O D. 15.3
3. Design a welded plate girder for a simply supported bridge deck beam with clear span of 20m, subjected to the following: Dead load including self-weight = 20kN/m Imposed load 12 kN/m Two-point loads = 150kN each spaced 2 m apart.