A W12x72 is used as a column and is supported by a concrete pier with top surface dimensions of 16 inch x 16 inch. f’c of column is 4,000 psi and is to carry a total service load of 250 kips with a Live load / Dead load = 3/2. Use LRFD solution. If B=N=14 inches, what is the minimum required computed thickness of the column base plate in inch? Express your answer in three decimal places. Use A36 for base plate.

A W12x72 is used as a column and is supported by a concrete pier with top surface dimensions of 16 inch x 16 inch. f’c of column is 4,000 psi and is to carry a total service load of 250 kips with a Live load / Dead load = 3/2. Use LRFD solution. If B=N=14 inches, what is the minimum required computed thickness of the column base plate in inch? Express your answer in three decimal places. Use A36 for base plate.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.13.2P

See similar textbooks

Similar questions

Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. O 212 kip O 202 kip O 196 kip 224 Wip
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
An under-reinforced beam section given below. What could be the maximum design load (Pa) on the beam. Materials C30/37 and B420C. Ignore beams' own weight! Pa Pd H A 2 m 2 m, 2 m B As 1500 mm² 300 mm > Cross-section 470 mm 30 mm
Determine the safe load of the column section shown, if it has a yield strength of 25 MPa. E = 200000 MPa. Use NSCP Specifications. Fyz248 mpa Properties of Channel Section d = 305 mm t₂ = 7.2 mm A = 3929 mm² t₁ = 12.7 mm Ix=53.7 x 10mm¹ x = 117 mm Properties of W 460 x 74 A = 9450 mm² b = 190 mm ly= 1.61 x 10 mm x = 17.7 mm tw = 9.0 mm rx = 188 mm ry = 41.9 mm d = 457 mm tr = 14.5 mm Ix = 333 x 10 mm Iy = 16.6 x 10mm* 7.21 When the height of column is 6 m. When the height of column is 10 m. Assume K= 1.0 457 CIVIL ENGINEERING- STEEL DESIGN
Problem 01 Using ASD, check the adequacy of the base plate (PL400X350×19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600KN and PLL = 320 kN. Use A-36 steel and concrete fc'=20 MPa. TH
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
2. The A-36 steel Bar BC had a diameter of 40 mm before the two loads, P, were applied. If after loading, the new diameter of the bar is 39.995 mm, what was P? P -1 m B 0.75 m 1 m
TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY FOUR 16 mm DIAMETER RIVETS AS SHOWN IN THE FIGURE. THE RIVETS USED ARE A502 GRADE 2, HOT DRIVEN RIVETS. THE STEEL IS ASTM A36 WITH Fy = 248 MPa AND Fu = 400 MPa. DETERMINE THE VALUE OF P. a. P BASED ON TENSION OF GROSS AREA b. P BASED ON TENSION OF NET AREA c. P BASED ON BEARING OF PROJECTED AREA d. P BASED ON SHEAR RUPTURE (BLOCK SHEAR)
Estimate for the concrete, formworks, reinforcement requirement of Beam GG-36. Length of Beam 1 = 8200mm Length of Beam 2 = 8200mm Size of Column = 800mm x 800mm GG-36 IGG-36 GG-131 009*00t GB-4 009*00+ GG-1
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the design tensile strength of the section based on yielding of the gross area. Answer: |0 O O О о
A simply supported beam shown below is HEA 400 of 5355 steel. It is laterally supported at points with an "X" The material properties and the section properties are given below. Use ASD load combination DL+LL and determine whether the beam has adequate flexural strength. Material: $355 Fy= 355 MPal Fu= 510 MPa E= 200000 MPa Section properties: A: 15900 mm² d: 390 mm h: 298 mm b: 300mm tr: 19 mm W 2311x10³ mm³ Iy: 8564x10*mm* A 4m t: 11 mm. İy: 73.4 mm W: 2563x10³ mm³ J: 189x104 mm DL: 150 KN LL: 100 KN 17 B 4m Cw: 2942x10⁹ mm C E: 200000 MPa