A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?

A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.68P

See similar textbooks

Similar questions

You are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…
Q3) A thermometer having a surface emissivity of 0.85 is placed in an air space in a metal-walled building, the walls of which may attain a temperature of -10°C during winter climate conditions. The convection coefficient between the thermometer and the surrounding air is estimated as h = 10W/m2. C. If the thermometer indicates a temperature of 17°C, estimate the true air temperature in the building.
Q2/ A small horizontal plate is in the shape of a square with a length of 5 cm. The plate is maintained at 50 C and exposed to water at 15 C. Calculate the heat loss.
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations? Known, Find, Schematic Diagram, Assumption, Properties, Analysis and Comments
A vertical cylinder 6 ft tall and 1 ft in diameter might be used to approximate a man for heat-transfer purposes. Suppose the surface temperature of the cylinder is 78°F, h=2 Btu/h · ft2 . °F, the surface emissivity is 0.9, and the cylinder is placed in a large room where the air temperature is 68°F and the wall temperature is 45°F. Calculate the heat lost from the cylinder. Repeat for a wall temperature of 80°F. What do you conclude from these calculations?
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
Calculate the over-all coefficient of heat transfer U for a piece of glass1/8-in thick, exposed to still air at 70 °F on one side and 0 °F air moving at15 mph on the other side.
Q2: A: The exterior wall of a single-story office building near Chicago is 3 m high and 15 m long. The wall consists of 100-mm face brick, 40-mm polystyrene insulating board. 150-mm lightweight concrete block, and an interior 16-mm gypsum. The wall contains three single-glass of 3 mm thickness windows 1.5 m high by 2 m long. Calculate the heat loss through the wall at design conditions if the inside temperature is (20 °C). The outside temperature is (-18 "C).
Air surrounding a light bulb is moving at 25 m/sec. The surrounding conditions are kept at atmospheric pressure and at temperature 25o C. The light bulb external surface is kept at 140o C. What is the heat transfer rate from the light bulb to the surrounding? Assume the light bulb as a sphere with a diameter of 50 mm.
1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at To = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant T, h Chip = 200 W/m2 · K, what is the maximum allowable chip power? If the coolant is a If the coolant is air and the corresponding convection coefficient is h dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?
A modern cabin has a concrete floor that is 4.50 inches thick. Aroaring fire keeps the interior of the cabin at 21.0 0C while the airtemperature below the cabin is a chilly 2.00 0C. How much heat(J) is lost through the concrete floor in 4 hrs if the cabin measures4.50 m by 6.50m to 3 sig fig?
1.19 A square isothermal chip is of width w = front surface is exposed to the flow of a coolant at T = 15°C. From reliability considerations, the chip temperature must not exceed T = 85°C. 5 mm on a side and is mounted in a substrate such that its side and back surfaces are well insulated; the Coolant Chip If the coolant is air and the corresponding convection coefficient is h = 200 W/m² · K, what is the maximum allowable chip power? If the coolant is a dielectric liquid for which h = 3000 W/m² · K, what is the maximum allowable power?