A valve in a glue factory fails open, and the thick,viscous glue overflows one side of a rectangular reservoir as shown. A 1-m widefilm of glue flows down the vertical reservoir wall at a rate of 0.04 m2/hr. If theviscosity of the glue is 3.2 N-s/m² and its density is 1080 kg/m³, what is thethickness of the overflowing film of glue flowing down the reservoir wall? Assumethe flow is steady, laminar and fully developed.Q- 0.04 m^3/hr

Given, Density of the glue,ρ=1080kg/m3Viscosity of glue,μ=3.2Ns/m2Flow…

Answered: A valve in a glue factory fails open,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Complete Solution please, thanks. 3. A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of-assume values with decimals between 3 to 4 m per second- enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack.
The 30cm long left coronary artery is 4.6mm in diameter. Blood pressure drops by 3.0mm of mercury over this distance. answer the following: part(A): what is the average blood speed through this artery?(express your answer with the appropriate units.) part(B): what is the volume flow rate in L/min through the artery?
In an oil pool, a small steel ball is released from the surface (y=0) without initial velocity. The strength of the resistance force exerted by the oil against the movement of the ball is directly proportional to the speed of the ball (Fd = k*V , k: constant). Neglect the buoyant force exerted by the oil. (m = 0.2kg, k = 0.843550 kg/s, g = 9.81 m/s^2). a-) What is the limit speed of ball ( Vlim)? b-) What is the time it takes for the speed of the ball to reach 99% of the limit speed after it is released from the surface? c-) What is the depth at which the ball's velocity reaches 99% of the limit velocity after it is released from the surface?
Question 2. An incompressible fluid flows steadily in the entrance region of a two dimensional channel of height 2h. Density of the fluid is 1.24 kg/m3. The uniform velocity at the channel entrance is U1=5.3m/s The velocity distribution at a section downstream is: 1- ()* и Umax Find out the maximum velocity umax in the downstream section in (m/s).
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = Answer J / kg. c. Energy Loss at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
Liquid is pushed through the narrow gap formed between two glass plates. Thedistance between the plates is h and the width of the plate is b . Assuming that theflow is laminar, two-dimensional and fully developed, derive a formula for thelongitudinal pressure gradient in terms of the volumetric flow rate, Q, the fluid viscosityand the distances b and h .In an example the above conditions apply with b = 0.10 m and h = 0.00076 m. Theliquid is glycerine that has an absolute viscosity of 0.96 N s/m². A pressure differenceof 192 kN/m² is applied over a distance of 0.24 m. Calculate the maximum velocity thatoccurs in the centre plane of the gap and the mean velocity.Answer 0.06 m/s
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3/hour. The length of the pipe is 35m and there are 2 elbows. Calculate the pump power requirement. The properties of the solution are density 975 kg/m3 and viscosity 4x 10-4 Pa s. a. Reynolds number = b. Energy Loss along a straight pipe = J/kg. c. Energy Loss in turns = J/kg. d. Total energy to overcome friction = J/kg. e. Energy to raise water to height = J/kg. f. Theoretical energy requirement of the pump kg ethanol/second = J/kg. g. Actual pump power requirement = watt.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
Your team is designing a chemical processing plant. You are the liquid handling and transportation specialist, and you need to transport a solvent (μ = 3.1 cP, ρ = 122k kg/m3) from a storage tank to a reaction vessel. Due to other equipment constraints, the fluid velocity must be 0.8 m/sec, and you must use stainless steel piping (ε = 0.00015 mm) with a total length (L) of 12 m. Determine the pipe inner diameter (ID) you will need to achieve a pressure drop of 0.3 kPa. Use the Moody chart.
A. A horizontal water jet hits a vertically mounted plate and an obliquely mounted plate as shown in Fig 2 (a) and (b), respectively. The jet is assumed to have the uniform velocity distribution of and the density of the fluid is p. The volume flow rate is Q. The effect of viscosity is assumed to be negligible. Answer the following questions. (b) y प्र2 (2) In the case of (b), the plate is mounted obliquely with the angle 0 to the x direction as shown in Fig 2(b). The jet is separated and the volume flow rates at the outlet become Qa and QB. (a) Obtain the force in the x direction Fix and in the y direction Fby exerted on the plate using p, Q, V and 0. (b) Obtain the volume flow rates Qa and QB using Q and 0. Fig. 2
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
A Closed tank of water with Length, I = 20 ft Height, h = 10.45 ft %3D Width, w = 5.6 ft Pgage = 0 kPa at the top before acceleration is accelerating at an angle of 38° with respect to the horizontal, where the x component of the acceleration is parallel to that of the length of the tank at a rate of 6.35 ft/s² . If the tank is 76% %3D full, calculate the pressure at the bottom of the left side of the tank and the force acting at the top of the tank during acceleration. Take note that the tank is fixed such that it remains parallel to the horizontal during acceleration

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS