A uniform beam, 1.5 metre long, is suspended in a horizontal position by two vertical supportrods as shown in the figure below. Rod A has a diameter of 12 mm and manufactured fromsteel with Esteel = 210 GPa. Rod B has a diameter of 16 mm and is made from copper withEcopper = 105 GPa. This simply supported beam is to carry a motor vehicle engine andgearbox weighing 5,5 kN.Determine the distance 'x' from the left-hand support 'A' in order for the beam to remainin a horizontal position.!Calculate the stress in each rod due to the applied load.Calculate the movement (extension) of the support wires under this 10 kN load.Will the rods be able to withstand the applied load? Motivate your answer.500 mm300 mmAB5.5 kN1500 mm

Simply supported beam: - It is a type of beam in which two supports one at each end. This beam is…

Determine the distance 'x' from the left-hand support 'A' in order for the beam to remain in a horizontal position. Calculate the stress in each rod due to the applied load. Calculate the movement (extension) of the support wires under this 10 kN load. Will the rods be able to withstand the applied load? Motivate your answer.

Determine the distance 'x' from the left-hand support 'A' in order for the beam to remain in a horizontal position. Calculate the stress in each rod due to the applied load. Calculate the movement (extension) of the support wires under this 10 kN load. Will the rods be able to withstand the applied load? Motivate your answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B1 in kN. 35KN В1 B2 ВЗ 10KN 15KN 30KN
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B2 =D 1.0 m; B;= 0.6 m. Determine the axial load acting on bar B, in kN. 35KN B1 B2 B3 10KN 15KN 30KN A 35 B) 20 C) 10 (D) 5
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2= 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN B1 B2 B3 10KN 15KN 30KN
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1 = 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN B1 B2 B3 ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B, in MPa. Determine the axial stress of bar B; in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B1 in mm. Determine the deformation of the bar B, in mm. Determine the deformation of the bar B3 in mm. 35 (A) 35 в) 20 10 (D 5
A Given the FLEXURAL RIGIDITY of the beam shown=6000 KN.m^2, find the :deflection at the roller support 2m B 3m C 3m 50 kN ID -0.025 m O No deflection O -0.125 m O +0.025 m O +0.125 m O Non of them O
NEED ANSWER ASAP!! A so-called "trapeze bar" in a hospital room provides a means for patients to exercise while in bed (see figure). The bar is 2.1m long and has a cross section in the shape of a regular octagon. The design load is 1.6kN applied at the midpoint of the bar, and the allowable bending stress is 240 MPa. Determine the minimum height h of the bar. Round to one decimal place. (Assume that the ends of the bar are simply supported and that the weight of the bar is negligible.) hmin=___mm
Q2: The pin-connected structure shown in figure below consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E= 105 GPa] with a cross-sectional area of A1= 290 mm2. Bar (2) is an aluminum alloy [E=70 GPa] with a cross-sectional area of A2= 650 mm?. If a load of P= 30 kN is applied at B, determine: (a) the normal stresses in both bars (1) and.(2) (b) the downward deflection of point B on the rigid bar. (1) 2250 mm 670 mm 480 mm 650 mm 1600 mm P = 30 kN
Determine the force in the member CE of the truss shown. It has F1=13 and F2-3 loaded as shown. Answer in two decimal places. Numerical values only. Don't indicate units here, just on the submitted solution. 2.53 m 2.07 m, -5.4 m F2 F1 2.25 m E F 4 m 3 m B)
1. The aluminum bar of cross-se ctional are a 0.6 in.2 carries the axial loads shown in the fig ure. Compute the total change in length, in inches, of the bar given that E = 10 x 106 psi. 6000 lb 4000 lb 7000 lb 5000 lb + 3 ft 5 ft to 4 ft Total change in length (in ches)
Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm
Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft 9 A B 1.5 ft 1.5 ft 1.5 ft 1.5 ft . F p C . E o D 1 of 1 0.4 ft Determine the shear force at point E. Express your answer in pounds to three significant figures. VE = Submit ▼ Part F ME = VAΣo↓ vec ΑΣΦΑ Out Request Answer Determine the moment at point E. Express your answer in pound-feet to three significant figures. VΠΙ ΑΣΦ | 11 | vec| 5 → www Doquent power www ? ? lb lb. ft
A 6m long solid bar of circle section has 140mm diameter for aluminum for length of 4m, while it has 120mm diameter for a length of 2m for steel bar, as shown in figure. Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take Est-200GPa, Eat 70 GPa. (20 140 I 300 Kn Aluminum 4 m Steel 2 m 300 Kn 120