A U - tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. The tube is held vertical and partially filled with liquid of surface tension 0.06 N / m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.

A U - tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. The tube is held vertical and partially filled with liquid of surface tension 0.06 N / m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm is:(0 = 0º)
In horizontal pipe, which of the following is constant? Pressure headElevation headVelovity head 12
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. 1m Liquid (s.g. = 0.88 ) 4 m B 2.6 m 1 m 幸 +
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine Fex (N) Fpr (N) The x-component of the reaction by the bend, FRx (N) and The y-component of the reaction by the bend FRY (N). de = 100 mm da = 150 mm 30° A
1) When a 2-mm-diameter tube is inserted into a liquid in an open tank, the liquid is observed to rise 10 mm above the free surface of the liquid. The contact angle between the liquid and the tube is zero, and the specific weight of the liquid is 1.2 x 10+ N/ m². Determine the value of the surface tension for this liquid.
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine a) The x-component of the reaction by the bend, FRx (N) and b) The y-component of the reaction by the bend FRY (N). ds = 100 mm da = 150 mm 30°
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
3. The tank shown has a parabolic curve gate at the bottom right side of length h perpendicular to the paper. The parabola has a vertex at the center of the hinge A. The parabola is defined by the equation in the X-Y coordinate system as shown. Neglecting the weight of the gate and the vertical reaction at the bottom end B of the gate, show the following if the unit weight of the liquid is y. Liquid surfac ILL hinge 2h 27 27 (a) The location of the vertical component ish from the y axis is 26 26 124 3 (b) The magnitude of the horizontal force P just to prevent the opening is yh³. h.
A glass tube of uniform bore is bent into the form of a square of sides a and filled with equal amounts of A three immiscible liquids of densities p, P2 and p3. It is known that P, P2 > (P3 + 2p;) G P3 (b) If the relative densities of the first and third liquids are 1.0 and 1.2 respectively, find the range of the relative densities of the second liquid which makes the above arrangement possible. B.
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the %3D figure. Determine the total resultant force acting on the gate and the location of the center of pressure. 6 ft 3ft VAVAVAVAVA Ib f Unit weight of the liquid (y) Value of hbar (h) Arca of the rectangular gate (A) Hydrostatic Force (F) Vahe of (Igx) Vahue of ybar (9) Location of the Hydro. Force measured from the water surface of the gate inclined (yel Ib ft ***answer Hydrostatic Force Fon the box below: Answer: 1311.03 The correct answer is: 1022.1
di de= Do Р 45° An involute pump casing is approximated as a toroidal shell as shown in the figure above. It has an internal cross-sectional diameter of d; = 490 mm, an overall external diameter of Do = 1420 mm, and a wall thickness of 4.7 mm. Point A is located at mid-thickness of the wall. (a) Express and in terms of the internal pressure p. Enter only the numerical value of the coefficient associated with p. Р A (b) Determine the maximum internal pressure the shell can hold, such that the Tresca stress intensity at point A does not exceed two-thirds of the yield strength oy = 250 MPa. MPa