A timber beam 100mmx200mm and 6m long has a steel plate 7mm thick rigidly attached at the bottom, with Ew = 690OMPa and Es = 200000MPA respectively. What is the maximum concentrated load P that can be placed at the center without causing in the timber flexural stress greater than 10MPA? Neglect the weight of the beam. See figure 05 below for the %3D %3D beam and section details.*

A timber beam 100mmx200mm and 6m long has a steel plate 7mm thick rigidly attached at the bottom, with Ew = 690OMPa and Es = 200000MPA respectively. What is the maximum concentrated load P that can be placed at the center without causing in the timber flexural stress greater than 10MPA? Neglect the weight of the beam. See figure 05 below for the %3D %3D beam and section details.*

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

A timber beam 150 mm wide and 200 mm deep is to be reinforced by bolting on two flitched each 150 mm x 12.5 mm in section. Find the moment of resistance when the flitched are attached symmetrically at the top and bottom. Allowable stress in timber is 6 N/mm². (Es= 20 Ew)
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)
a laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 kPA. and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the bam on a 4.5 m simple span.
A TIMBER BLOCK "B x B" mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A "B" mm AND 't' mm THICK STEEL PLATES. DETERMINE THE THICKNESS 't' SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY. B t B t PROB 04
The built-up beam wooden above is subjected to a horizontal shear force, V, as shown. Assume that the beam dimensions are drawn to scale. Also assume that the nails attaching the three pieces of the cross-section allow it to act as a single member. Which of the following best explains why we cannot analyze the shear stresses in this beam with the techniques covered in this class (at least, so far)? The shear force is not "transverse" O Wood cannot be loaded perpendicular to the grain The shear force is not acting along a line of symmetry of the cross-section We can only deal with vertical shear forces
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
Design the shear reinforcement of the beam loaded as shown using USD with fc’ = 20.7 MPa and fy = 276 MPa
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
Determine the numbers of rebars required for a RC beam (h=400mm, b=700mm) carrying a factored moment of 796 kPa. The concrete used has a compressive strength of 28MPa, while steel yields at 345MPa. Assume single layer of reinforcements (compression and/or tension side) and do not check for rebar spacing anymore. Other parameters: Cc = 40mm db = 20mm ds = 10mm Provide illustration if necessary and answers must be in 3 decimal places.
Design the shear reinforcement of the beam loaded as shown using USD with fc’ = 20.7 MPa and fy = 276 MPa, fs = (fy/2)
a 450mm diameter concrete spiral column is to be designed to support a factored axial load of 3170kn. clear bar cover is 40mm and tge aggregate soze is 25mm. use nscp 2010 with fc'= 28mpa, fy= 414mpa for longitudinal steel, fyt= 414mpa for spiral steel. limit the gross percentage to 2%. which of the following most nearly gives the clear spacing of the main longitudinal reinforcements in mm.