A three-phase transmission line and a telephone line are supported on the same towers a shown in the figure. The power line carries a 60-Hz balanced current of 200-A per phase . the telephone line is located directly below phase b. assuming balanced three-phase currents in the power line, find the voltage per kilometer induced in the telephone line. 3.6 m 3.6 m Da1 Da2 Del De2 4 m

A three-phase transmission line and a telephone line are supported on the same towers a shown in the figure. The power line carries a 60-Hz balanced current of 200-A per phase . the telephone line is located directly below phase b. assuming balanced three-phase currents in the power line, find the voltage per kilometer induced in the telephone line. 3.6 m 3.6 m Da1 Da2 Del De2 4 m

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.25P: Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows:...

See similar textbooks

Similar questions

What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
a. i. Why do power systems operate in an interconnected arrangement? ii. How is the frequency controlled in a power system? iii. What is meant by the stiffness of a power system? b. Two 50 Hz power systems are interconnected by a tie-line, which carries 1000 MW from system A to system B, as shown below. After the outDage of the line shown in the figure, the frequency in system A increases to 50.5 Hz, while the frequency in system B decreases to 49 Hz. i. Calculate the stiffness of each system. ii. If the systems operate interconnected with 1000 MW being transferred from A to B, calculate the flow in the line after outage of a 600 MW generator in system B. 1000 MW A В
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
please solve for nodal stress method. (if it is possible to apply supernodes)
Q2 (a) Three-phase generator consist of three set of single-phase generators, with voltages equal in magnitude but differing in phase angle by 120° apart. (i) Sketch phasor diagram of the three-phase voltages VA, VB and Vc (ii) Plot the three-phase voltages waveform in Q2(a)(i) in single plot.
The one-line diagram of a three-phase system is shown in Figure 1. By selecting a common based of 90 MVA and 32.75 kV on the generator bus, all impedances including the load impedance in per-unit are as follows: XG (new) = j0.1421 p.u XT1 (new) = j0.1219 p.u XT2 (new) = j0.1219 p.u ZOH = 0.0016 +j 0.0083 p.u Хм пеw) 3D j0.247 р.u ZLoad = 2.2759+ j1.2306 p.u T1 T2 90 MVA Motor 90 MVA 55 MVA 33/275 kV 275/11kV 10.95 kV XT=12% Xr3=12% Xx=15% Generator 95 MVA M 32.75 kV Xg=15% 2 x OH Line 138 km R = 0.01 ohm/km X = 0.05 ohm/km Load 35 MVA 10.95 kV 0.88 pf lagging Figure 1 Note: Region 1 = Generator bus Region 2 = Transmission Lines busses Region 3 = Load Bus If the motor operates at full load 0.88 power factor lagging at a terminal voltage 10.95 kV, determine the voltage at the generator bus bar.