A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S₁, S₂) are given in the figure. To Vaccum Pump Patm P₁ S₁ = 0.88 Fluid I S₂ = 0.95 Fluid II Patm Fluid III: Water Unit weight of water, Ym = 9.81 kN/m³ Atmospheric Pressure, Patm = 95.43 kPa The gauge pressure value (in kN/m², up to two decimal places) of p1 is 754 0.5 m 1.0 m 1.5 m

A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S₁, S₂) are given in the figure. To Vaccum Pump Patm P₁ S₁ = 0.88 Fluid I S₂ = 0.95 Fluid II Patm Fluid III: Water Unit weight of water, Ym = 9.81 kN/m³ Atmospheric Pressure, Patm = 95.43 kPa The gauge pressure value (in kN/m², up to two decimal places) of p1 is 754 0.5 m 1.0 m 1.5 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(a) Glycerine at 25 °C flows through a straight copper tube (D = 73.8 mm), at a flow rate of 180 L/min. Calculate the pressure difference between 2 points which are 25.8 m apart, if the first point is 0.68 m below the second point. Gven: At 25 °C density and dynamic viscosity for glycerine is 1286kg/ and 0.96 Pa.s respectively(b) If benzene at 50 °C is used in question (a) above instead of glycerine, evaluate the new pressure difference. ...
In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
Orifice Given:As = 3m2C = 0.92Ao = 0.01m2 Determine the time for the depth of liquid in the tank to be 0.8m
Flow rate of a fluid (p = 1000 kg/m³) in a small diameter tube is 800 mm³/s. The length and diameter of the tube are 2 m and 0.5 mm, respectively. The pressure drop in 2 m length of is equal to 2 MPa. The viscosity of the fluid is:
A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S,, S,) are given in the figure. To vacuum pump P. S, = 0.88 Fluid I 1 1.5 m P 1 1.0 m 0.5 m Pm S, = 0.95 Fluid II Fluid III : Water Unit weight of water, Y. =9.81KN/m³ Atmospheric pressure, Pam = 95.43kPa The gauge pressure value (in kN/m²) up to two decimal places of p, is
Flow rate of a fluid (density = 1000 kg/m³) in a small diameter tube is 800 mm³/s. The length and the diameter of the tube are 2m and 0.5 mm, respectively. The pressure drop in 2m length is equal to 2.0 MPa. The viscosity of the fluid is
Problem 2 -50 A glass 12 cm tall filled with water is inverted. The bottom is open. What is pressure at the closed end? Barometric pressure is 101.325 kPa. the Ans: 100.15 kPaa Problem 2 -51 In Figure 13, in which fluid will a pressure of 700 kPa first be achieved? Ans: glycerin Po = 90 kPa ethyl alcohol p= 773.3 kg/m 60 m oil p= 899.6 kg/m? 10 m water p = 979 kg/m glycerin p = 1236 kg/m 5 m 5 m
a) When oil (p=850 kg/m³) flows through a 5 cm diameter horizontal pipe of 12 m length at a velocity of 1.2 m/s a pressure difference of 5000 N/m² is recorded. i) Assuming laminar flow calculate the viscosity of the liquid. ii) Check that the assumption of laminar flow is valid b) Air (p=1.287 kg/m³) flows into a jet engine of diameter 1.2 m as shown in Figure Q4b at a velocity of 90 m/s. Upon landing, the engine exhaust exits through the reverse thrust mechanism with a speed of 275 m/s symmetrically in the directions indicated. Assume that the inlet and outlet pressures are atmospheric and that the mass flow rate of fuel is negligible compared to the air flow rate through the engine. i) Determine the x and y velocity components of the exhaust leaving the engine ii) Evaluate the horizontal and vertical forces experienced by the engine C3=275 m/s (3) C1=90 m/s 1.2 m diameter (1) 30 degree (2) C2=275 m/s Figure Q4b
Consider the problem of draining a hemispherical tank of radius H* feet that is full of water and has a circular drain hole of radius 3 inches at the bottom. How long will it take for the tank to empty? dv When the change volume is = -kA/2gh(t) A is the constant cross sectional area of the opening; and k is a constant determined by the viscosity of the fluid dh dt H H-h dV 1 dt dt ar² Note: Draining a hemispherical tank. Take H* as a last two digits of your ICEM ID, if last two digits less than 10 take H= 18 feet
2. A cylindrical tank 1.5m in diameter contains a column of 3 immiscible liquids with SG 0.8, 1.0, and 1.8. Each of the liquids have heights of 0.5m. There is a 50mm diameter orifice at the bottom of the tank. Solve the time needed to drain the first liquid, time needed to drain the second liquid, and time needed to fully drain the tank. Hint: For layered fluids similar to this problem, before plugging the given into the Bernoulli's Equation, you have to convert the heights of the other fluids to the equivalent height of the fluid that is presently being drained. Heights of different fluids are equivalent if they will result to the same pressure at the bottom. As an example, an 8m high water (SG = 1.0) will produce the same pressure at the bottom as a 10m high oil (SG = 0.8). Thus, an 8m high water is equivalent to a 10m high oil. Yoil hoil P = Yw hw =
2) Assuming we have a fluid with SG=0.6, and height of fluid in the piezometer tube equal to h=10m, what is the pressure at the M, P, S? PM =? Pp =? Ps = ? M
The liquid surface in a peizometer attached to a conduit stands 1.0 m above point A, as shown in fig. 2-30. Find the pressure at point A if the liquid is (a) water and (b) mercury. The answer was already given, please show the solution. ANSWER: (a) 9.79 kPa (b) 133 kPa