A thermal efficiency of a combustion chamber valued equal to 73.15% with heat supplied to the system equal to 125 BTU. Calculate the net work produced in KJoules? 85.546 Kjoules 91.895 Kjoules 102.346 Kjoules 212.751 Kjoules

A thermal efficiency of a combustion chamber valued equal to 73.15% with heat supplied to the system equal to 125 BTU. Calculate the net work produced in KJoules? 85.546 Kjoules 91.895 Kjoules 102.346 Kjoules 212.751 Kjoules

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter31: Gas Heat

Section: Chapter Questions

Problem 5RQ: The specific gravity of natural gas is A. 0.08. B. 1.00. C. 0.42. D. 0.60.

See similar textbooks

Related questions

Q: Draw the shear and moment diagram of the loaded beam shown below and determine the maximum moment…

Q: Part A The 12-lb block has a speed of 4 ft/s when the force of F= (8t) lb is applied. The…

Q: a) If the spring is cut by half of its length and is loaded by the same load, compute the…

Q: The ends of the triangular plate are subjected to three couples. Determine the magnitude of the…

Q: Water is flowing in an open channel at a depth of 2 m and breadth of 3 m and a velocity of 3 m/s.…

Q: 10. At a temperature of 30 °C, the pressure of the gas in a deodorant can is 3 atm. Calculate the…

A: The volume remains constant. The ideal gas equation is used for both the cases to get the pressure…

Q: Q19/ The value of the normal stress due to flexural force 10 kN applied on * :the beam at point F is…

A: (Q-19) The value of normal stress due to flexural force 10 kN applied on the beam at point F is 13.5…

Q: Problem 8.14 A curved bar of circular cross-section 100 mm in diameter has a radius of curvature of…

A: We know that a curved bar with a circular cross section of 100 mm in diameter and a radius of…

Q: cof R-134a at an initial pressure of 1.2 MPa is filled in a rigid container with a volume of 24.228…

A: Given data mass of R134 = m = 1 kg Initial Pressure = P1 = 1.2 MPa Volume = V1 = V2 = 24.228 m3

Q: Determine the Resultant Moment at A Determine the Resultant Moment at B Determine the Resultant…

A: Given Force system To find Moment at A Moment at B Moment at C

Q: As the engineer working in a car company, you are assigned to evaluate two new car models, the Car A…

A: Normal speed of an article during a given time stretch is the adjustment of its position partitioned…

Q: 3. Calculate the torque and the rotation speed at the input pulley if the output pulley needs to…

A: (a) The torque at the input pulley is 66.67 lb•in. (b) The rotational speed of the input pulley is…

Q: Draw the shear and moment diagram of the loaded beam shown below and determine the maximum moment…

Q: What is the turbine efficiency of a Hydro electric power plant if the total power efficiency is…

Q: 2. Gas (p = 0.0022 lb/ft³) flows through duct shown in fig. At A flow rate is 60 ft³/s under a…

A: Given Data The density of the gas is: ρ=0.0022 lb/ft3 The flow rate of the gas is: 60 ft3/s The…

Q: 5 kg of steam at 10 bar was sampled and passed to a barrel calorimeter whose water equivalent at…

Q: A golf ball is struck with a velocity of 80 ft/s as shown. Determine the distance d to where it will…

A: Given DataV=80ft/sθ=45°

Q: 27 mm wide by 3 mm thick and 1.3 m long, is bent by couples applied at the ends so that the midpoint…

Q: 4 kg mass A and 4 kg mass B slide on the smooth horizontal bar with the initial velocities given.…

A: Given data: mA=mB=m=4 kguA=10 m/suB=-5 m/s Need to determine the velocity of each slide after…

Q: A system consisting of 2 kg of water initially at 100°C, 10 bar undergoes an internally reversible,…

Q: 0, JA centrifugal pump used to take water from reservoir to another through 800 m ength and 0.15 m…

A: Given that, Length of the pipe, L=800 m,Diameter of the pipe, D=0.15 m,Difference in two tank, ∆z=8…

Q: THE SPRING RATE FOR EACH OF THE SPRING ATTHE 1ST LEVEL ARE ALL 270 Mm, 2NO LEVEL AT IBO Nim AND 3RD…

A: The first level deflection can be determined as shown below.

Q: Determine the tension developed in cach cord required for cquilibrium of the 20-kg lamp. 45

A: Answer: (a) TCD = 339.8284 N (b) TDE = 392.4000 N (c) TAC = 242.7345 N (d) TBC = 274.6224 N

Q: What is the actual power generated in KW by a Tidal power plant if it has 62.35 % efficiency and if…

A: Efficiency, η= 62.35%= 0.6235 Barrage area, A= 1550 m2 Seawater density, ρ= 1030 kg/m3 Vertical…

Q: Q2/ A compound cylinder is formed by shrinking a tube of 250 mm internal diameter and 25 mm wall…

Q: 4. Steam turbine with 80% stage efficiency receives steam at 7MPA and 550 deg C and exhausts as…

A: Find the quality after turbine expansion.

Q: Q2: A petroleum product is pumped at a rate of 2.32 x 10 m/s from a reservoir under atmospheric…

Q: A crude oil with a density of 875 kilogram per cubic meter is pumped and flowing at 1.5 meter per…

Q: Which of the following statements describes the third law of thermodynamics? -The enthalpy of the…

Q: The force P is applied to the 38-kg block when it is at rest. Determine the magnitude and direction…

Q: A steam engine develops 45 BHP with dry saturated steam at 1.03425 MPa and exhaust at 0.12411 MPa.…

Q: A car weighing 3000 lb, with a wheel base of 9 ft. carries 1300 lb of its load on the front wheels.…

Q: A R-134A vapor refrigeration cycle cycle operates at an evaporator temperature of 20 Celsius and a…

A: The COP is the amount of energy provided from any engine or the the cycle when an amount of input we…

Q: Please show all work. will upvote, thanks An input force f = F‧sin(ωt) is applied to the body in…

Q: The efficiency of a fan, 7, can be expressed as a function of fan's diameter, D, its angular…

A: Given: Diameter of the fan=D Angular velocity of the fan=ω kinematic viscosity=v Discharge of the…

Q: Determine the reactions at A and B for the loaded beamas shown in Figure

Q: A coil of resistance 52 and inductance 120 mH in series with a 100 µF capacitor, is connected to 300…

A: Now, the below figure shows the circuit diagram of the given data :

Q: Equation of Equilibrium. Referring to the free-body diagram of the beam shown in Fig. a, +1£F, = 0;…

Q: 0,JA centrifugal pump used to take water from reservoir to another through 800 m sength and 0.15 m…

A: Given: Length of the pipe→L=800 m Diameter of the pipe→D=0.15 m Head difference in both tanks→∆h=8 m…

Q: A two-blade wind turbine is exposed to 60 mile/h wind. Downstream of the propeller the wind speed is…

Q: Given the image below, what is the correct force diagram that shows the reactions of the supports

Q: A system consisting of 2 kg of water initially at 100°C, 10 bar undergoes an internally reversible,…

Q: 3.23 A small, high-speed turbine operating on compressed air produces a power output of 100 W. The…

Q: A cantilever beam, 80 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

A: Find the normal stress in a fiber 70 mm from the top of the beam at a section 5 m from the free end.

Q: 0, JA centrifugal pump used to take water from reservoir to another through 800 m sength and 0.15 m…

A: The total head required by the pump can be determined as shown below.

Q: 1.5 (3-x Q1) Evaluate the integral * dy dx using polar coordinate

Q: 1. An engine operating on the air diesel cycle with k-1.3 has thermal efficiency of 63% and a…

Q: 8-22. The cylinder is confined by the brake, where 4, 0.4. Determine the required compression in the…

A: Given: The coefficient of friction, µ = 0.4 The torque, T = 800 N.m The spring stiffness, k = 3…

Q: 1.5 3-х Q1) Evaluate the integral S* dy dx using polar coordinate

Q: Given the picrture below, which of the following shows a single force equivalent to the force and…

A: Consider the diagram as shown below for the resolved force P.

Question

A thermal efficiency of a combustion chamber valued equal to 73.15 % with heat supplied to the system equal to 125 BTU. Calculate
the net work produced in Kloules?
85.546 Kjoules
91.895 Kjoules
102.346 Kjoules
D 212.751 Kjoules

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The combustion chamber of a diesel power plant has a theoretical heat value of 102 K Joules in a 98 25% combustion efficiency. What is the actual heat released in the systern in BTU? 90.44 BTU 94.99 BTU 98.55 BTU 99.98 BTU
30. A cylinder contains an amount of gas. At pressure of 470 kPa and at temperature of 27 ̊C, thegas occupies a volume of 0.03 m3. It is then compressed according to Boyle’s law until its pressureis 1.3 MPa, and then expanded according to Charles’ Law until its volume is 0.02 m3. Calculate thefinal temperature of the gas. a. 292.35000C b. 248.85000C c. 216.22500C d. 280.31810C
A piston cylinder arrangement initially contains 7.0 kgs of super- heated steam at 500 kPa and 250 C, now heat is removed until 44% condenses. 1) What is the amount of heat removed in (kJ)? 13935.32 11152.41 10432.49 7472.29 8357.65 6817.34 Not listed 12703.96 • 9243.01 2) What is the final volume (m )? O0.8448 1.0018 1.6297 1.2634 1.7866 1.1588 1.3681 1.4727 Not listed
A diesel power plant has an overall efficiency of 30%. If the calorific value of diesel is 18000 BTU/lb and cost P6.000 per liter, how much is the fuel cost of production per KWHR of energy? Take the density of diesel as 900 grams per liter. A. P1.91/KWHR B. P1.85/KWHR C. P2.12/KWHR D. P2.45/KWHR
A Boeing 767 due to fly from Montreal to Edmontonrequired refueling. Because the fuel gauge on the aircraft was not working, a mechanic used a dipstick todetermine that 7682 L of fuel were left on the plane.The plane required 22,300 kg of fuel to make the trip. Inorder to determine the volume of fuel required, thepilot asked for the conversion factor needed to converta volume of fuel to a mass of fuel. The mechanic gavethe factor as 1.77. Assuming that this factor was in metric units the pilot calculated the volume to beadded as 4916 L. This volume of fuel was added andthe 767 subsequently ran out the fuel, but landed safelyby gliding into Gimli Airport near Winnipeg. The errorarose because the factor 1.77 was in units of pounds perliter. What volume of fuel should have been added?
A piston cylinder arrangement initially contains 7.0 kg of super-heated steam at 100 kPa and 250 oC, now heat is removed until 0.58 condenses. 1) What is the amount of heat removed in (kJ)? 12210 10946 11262 11736 11894 Not listed 2) What is the final volume (m3)? 4.9847 Not listed 4.5108 5.2220 4.2735 4.7479
b) For an Otto Engine the temperature at the end of combustion is 280 K. If the temperature in the gas side and coolant side of the wall are 177 °C and 127 °C and cylinder wall thickness is 5 mm;
28. The edges of a cast iron block weighing 32 kg were rounded off with a mill. When the block was reweighed, it was found to weigh only 29,5 kg. What percentage of the original cast iron block was lost? A. 7.8% В. 8.5% С. 3.4% D. 2.5% 29. If 3.5 L of used oil were to be disposed of each week over a three-year period, the total number of liters disposed of at the end of this time, assuming there are 52 weeks in a year, would be A. 495 L В. 546 L
A diesel electric plant supplies energy by Meralco. During a 24 hour period, the plant consumed 200 gallons of fuel at 28 deg. C and produced 3930 kw-hr. Industrial fuel used is 28 degree API and was purchased at 5.50 per liter at 15.6 deg. C. What should be the cost of fuel to produce 1 kw-hr? a. 1.10 b. 1.05 c. 1.69 d. 1.00
A piston cylinder arrangement initially contains 7.0 kg of super-heated steam at 100 kPa and 250 C, now heat is removed until 0.62% condenses. 1) What is the amount of heat removed in (kJ)? 11262 10946 11894 12210 None of the above 2) What is the final volume (m")? 4.2735 4.5108 4.9847 5.222 None of the above
If 250(ft)3(s) of air at 122(°F) and approximately atmospheric pressure is preheated for a combustion process to 932(°F), what rate of heat transfer is required?
29. A cylinder contains an amount of gas. At pressure of 460 kPa and at temperature of 27'C, the gas occupies a volume of 0.08 m³. It is then compressed according to Boyle's law until its pressure is 1.2 MPa, and then expanded according to Charles' Law until its volume is 0.05 m³. Calculate the final temperature of the gas. a. 292.3500°C b. 248.8500°C c. 216.2250°C d. 280.3181°C