A tensile stress of 7000 psi is developed in the straight shank of a ½ in diameter bolt that is used to secure two pieces of wood. If there are washers employed at both the head and nut, what is the approximate area of the washers considering that the allowable bearing stress in the wood is 95 psi? A 12.2 sq. in B. 14.5 sq. in. C. 11.7 sq. in D. 10.1 sq. in

A tensile stress of 7000 psi is developed in the straight shank of a ½ in diameter bolt that is used to secure two pieces of wood. If there are washers employed at both the head and nut, what is the approximate area of the washers considering that the allowable bearing stress in the wood is 95 psi? A 12.2 sq. in B. 14.5 sq. in. C. 11.7 sq. in D. 10.1 sq. in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The construction of the post is shown below. The mechanical tube has an OD of 3.0 in and a thickness of 0.220 in. The concrete foundation has a dimension W of 8 inches. What is the largest load F, in kips, that can be applied if the bearing stress between the mechanical tubing and the steel plate is 80 ksi? F a. 96.7 b. 124 W W C. d. 132 154 Mechanical tubing Steel plate Concrete
5. Which area of the aircraft is subjected to hoop stress? Wings Control Surfaces а. b. Engine Cabin C. d. 6. The stresses experienced by aircraft during take off and landing are the same 7. It describes how well the substance can be hammered into sheets Toughness Malleability Ductility а. b. С. d. hardness 8. Wing mounted podded engines and integral fuel tanks Reduce the visibility of the passengers Provide increased safety if the undercarriage collapses on landing Reduce tailplane down load Provide wing bending relief A. В. C. D. 9. Which of the following choices is true about box beams? () closed section box beams is used in aircraft wings (ii) closed section box beams is capable of resisting torsional loads A Both (1) and (ii) are false Both (i) and (ii) are true and (ii) is not the correct reason for (i) (1) is true but (ii) is false Both (i) and (ii) are true and (ii) is the correct reason for (i) B
5. The construction of the post is shown below. The mechanical tube has an OD of 3.0 in and a thickness of 0.220 in. The concrete foundation has a dimension W of 8 inches. What is the largest load F, in kips, that can be applied if the bearing stress between the mechanical tubing and the steel plate is 80 ksi? a. b. 96.7 124 W a. 10.7 b. 12.4 F W c. d. 132 154 Mechanical tubing Steel plate Concrete 6. A 6 mm diameter rod, of unknown material, is subjected to 10 kN tensile load. In the process, its length increased from 70 mm to 72 mm. If stress is proportional to strain, determine the modulus of elasticity, in GPa, of the material? C. 19.5 d. Answer is not among the choices
From the given bracket shown, which consist of two plates riveted to the column by 4-22mm Ø rivets which is subjected to an eccentric load of 150 kN. 1. Which of the following gives the shearing stress due to axial load only? a. 49.325 MPa b. 70.25 MPa c. 80.47 MPa d. 68.25 MPa 2.. Which of the following gives the shearing stress due to moment alone? a. 69.76 MPa b. 70.94 MPa c. 56.39 MPa d. 64.32 MPa 3. Which of the following gives the maximum shearing stress? a. 110.30 MPa b. 120.40 MPa c. 140.50 MPa d. 105.70 MPa
The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 2. If allowable bearing stress in holes is 1.2Fu where Fu is the ultimate strength of the plate and which is equal to 400 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 563.3 kN b. 460.8 kN c. 683. 6 kN d. 405.9 kN 3. If allowable yielding of gross area is Fy/1.67, where Fy is the yield strength of the plate and which is equal to 250 MPa, find the maximum allowable force P that can be applied neglecting effect of eccentricity. a. 534 kN b. 560 kN c. 446 kN d. 503 kN 4. If diameter of hole equals diameter of rivet, what is the net area of edge-3-4-edge in square millimeters? a. 2540 b. 2590 c. 2880 d. 2040
b.The strong room of a school where an exam question papers are kept is made up ofrectangular metal bars.One bar has a width of 10 mmand would beable to withstand a maximum compressive stress of 20 MPa. i.Prove that,the minimum breadth of thisbar can withstand a burdened with a force of 3 KN. ii.If the bar in question is 2 mlong and decreases in length by 0.25 mmwhen aforce isapplied, then show thata percentage strain can be obtained. iii.What would be its Modulus of Elasticity, E?
1.A 3inch by 3inch square steel guardrail post was hit by a car on one of its side and applieda 1.6 kN force. The base of the post is a ¼ inch thick square steel plate and is supported by four pieces half inch diameter bolts. (1 inch = 25.4 mm) a.Assuming that the bolts received an equally distributed force, what is the shear stress applied to a single bolt? b.If the bottomplate of the post is a steel with astress capacity of 120 MPa, what is the maximum allowable bearing force on the plate? c.Assuming that the post is a solid steel and was hit by a falling solid heavy object from above, what is the maximum load that it can carry? d.If the post is a steel tube withcircular hollow section and an outerdimension of 4 inch by 4 inch, what is the maximum inner diameterif same force was applied?
Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Determine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What furce is required to punch a square hole (25-mm 25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm *2 mm 30 mm Nck
Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detemine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. R. What fore is requirod to punch a square hole (25-mm 25mm) in a plate that is 30 mm thick? The shear strength is 350 MN'm2. Purcha 2 mem 25 mm 30 mm thick.
A bronze strip is securely fixed to a side of a steel strip of the same thickness, width and length. The steel has a Young's modulus which is twice that of bronze. When the compound bar is loaded in tension, the force in steel is : F F Oa. Same as that in bonze, and equal to F/2 O b. Same as that in bronze, and equal to F Oc. Twice that in bronze, and equal to 2F/3 Od. Half that in bronze, and equal to F/3
This is my Question... Determine the vertical displacement of joint C . EA is constant Determine the Vertical Displacement of the Joint C. EA is Constant Thank You Very Much
In the hanger shown, the upper portion of link ABC is 3/8 in. thick,and the lower portions are each 1/4 in. thick. Epoxy resin is usedto bond the upper and lower portions together at B. The pin at Ais of 3/4 in. diameter while a 3/8 in. diameter pin is used at C.Determine:(a) the shearing stress in pin A (b) the shearing stress in pin C (c) the largest normal stress in link ABC (d) the average shearing stress on the bonded surfaces at B (e) the bearing stress in the link at C