A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and %3D the torques are T1 = 19 kip-in. and T2 = 11 kip-in. Calculate the shear stress at segment %3D %3D AB in ksi. Note Round up final answer to whole number T2 d2 B |C L - -L2-

A stepped shaft ABC consisting of two solid circular segments is subjected to torques T1 and T2 acting in opposite directions, as shown in the figure. The larger segment of the shaft has diameter d1 = 2.25 in. and length L1 = 30 in.; the smaller segment has diameter d2 = 1.75 in. and length L2 = 20 in. The material is steel with shear modulus G = 11 x 10^6 psi, and %3D the torques are T1 = 19 kip-in. and T2 = 11 kip-in. Calculate the shear stress at segment %3D %3D AB in ksi. Note Round up final answer to whole number T2 d2 B |C L - -L2-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm
The circular shaft AB consists of a 19 mm diameter solid steel cylinder in which a 5 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 59 Nm. What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal place without +/- sign. L₁ L₂ C 150 Nm B
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
A fiber tube with a regular polygon shape shown is 4.5 ft long, has thickness of 0.05 in. and side dimension of 2 in (refer to the white line) Determine the following: a constant wall 6. The largest torque (in lbin) that the tube can carry if the shear stress is limited to 7500 psi. 7. The angle of twist this torque. use G = 5 x 106 psi. (in degrees) caused by 8. The deformation (in inches), if the tube is fixed at the other end, and is pulled by a 2-kip force, E = 4 x 106 psi. Hint: Estimate by the area as thickness multiplied perimeter.
A stepped shaft is as in Figure 5-13. The AB part is aluminum (G = 28GPA) and the BC part is steel (G= 84GPA). The aluminum part has a solid circular section with a diameter of 45 mm and the steel part has a circular head section with an outer diameter of 60 mm and an inner diameter of 30 mm. Find the maximum shear stress in each material and the torsion angle at B at which the torsion moment of 4000 N.m is applied. A and C terminals are rigidly connected.
2)For the supporting frame shown below: a) Determine the internal forces acting at section a-a. b) Determine the stress components that act at points A and B. IN = 2.6525x10-7 mª -300 mm 150 mm 2.5 kN a 12 mm 6 mm 6 mm 6 mm 36 mm'36 mm Section a – a
A circular steel tube of length L = 1.5 m is loaded in torsion by torques T (see figure). T r2 (a) If the inner radius of the tube is r, = 41 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00026 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)? mm Enter a number.
A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside diameter d1= 80mm. The tube is 2.80m long, and the aluminum has a shear modulus of G= 28GPa.a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist, in degrees,when the maximum shear stress is 52MPa?b. What diameter d, in mm, is required for a solid shaft, as shown, to resists the same torque with the same maximum stress?c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft?
Consider the nonprismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radiusr) in segment 2. The beam is loaded by a downward traingular load with maximum intensity go as shown. Linear M. 3 Segment 1 0.5 EI Segment 2 EI (a) Find expression for maximum compressive stress at point 1. (b) Find expression for maximum tensile stress at point 1.
Problem 3.3. A solid brass rod AB and a solid aluminum rod BC are connected together by a coupler at B, as shown in Figure ( problem 3.3).The diameters of the two segments are di=60 mm and d2 =50 mm, respectively. Determine the axial stresses of (in rod AB) and o2 (in rod BC). d (1) dz B_ 150 kN (2) 50 kN Figure (problem 3.3)
A circular steel tube of length L = 1.1 m is loaded in torsion by torques T (see figure). T L r2 (a) If the inner radius of the tube is r, = 49 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00041 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)max (in mm)? mm
A thin rectangular polymer plate PQRS of width b = 361 mmand height = 193 mm is shown in the figure. The plate is deformed so that corner Q is displaced upward by c = 3.1 mm and corner R is displaced leftward by the same amount. Determine the shear strain at corner P after deformation. a Y = b S a urad