A steel pipe 150mm diameter conveys steam at a temperature of 260 degrees and is covered by two layers of lagging, each 50mm thick. The thermal conductivity coefficient of the inside layer of lagging is 0.086W/m.K while that of the outside layer is 0.055W/m.K. The outside surface temperature of the steel pipe can be taken as the same as the temperature of the system. The ambient temperature is 27 degrees. Calculate the heat lost per hour for pipe length 30m. Calculate the interface temperature between the two layers of lagging

A steel pipe 150mm diameter conveys steam at a temperature of 260 degrees and is covered by two layers of lagging, each 50mm thick. The thermal conductivity coefficient of the inside layer of lagging is 0.086W/m.K while that of the outside layer is 0.055W/m.K. The outside surface temperature of the steel pipe can be taken as the same as the temperature of the system. The ambient temperature is 27 degrees. Calculate the heat lost per hour for pipe length 30m. Calculate the interface temperature between the two layers of lagging

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.48P

See similar textbooks

Similar questions

Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = kJ / hour. b. Temperature between insulation layers. = ° C
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 500 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 8 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = Answer kJ / hour. b. Temperature between insulation layers. = Answer ° C.
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to deliver steam with a pressure of 800 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Heat loss per hour. = AnswerkJ / hr. b. Temperature between insulation layers. = Answer ° C.
Steel pipe (outer diameter 100 mm) is covered with two layers of insulation. The inner layer, 40 mm thick, has a thermal conductivity of 0.07 W / (m K). The outer layer, 20 mm thick, has a thermal conductivity of 0.15 W / (m K). Pipes are used to delivering steam with a pressure of 600 kPa. The temperature on the outer insulation surface is 24 ° C. If the pipe is 10 m long, determine the following: (assuming that the conduction heat transfer resistance of the steel pipe and the vapor convection resistance are negligible). a. Hourly heat loss ... (kj / hr)b. temperature between insulation layers ... (° C.)
Calculate the quantity of heat conducted per minute through a duralumin circular disc 127 mm diameter and 19 mm thick when the temperature drop across the thickness of the plate is 5 degrees Celsius. Take the coefficient of thermal conductivity of duralumin as 150 W/(m-K).
The cylindrical pipe with a thread diameter of 0.070 m and an internal diameter of 0.050 m is insulated both internally and externally. Calculate the heat loss per unit length of the pipe (1 m) when the inner surface temperature of the pipe is kept at 50 °C and the outer surface temperature at 20 °C (Average thermal conductivity constant = Km= 0.172 J/cm.s.K).
2. A steam line is covered with two successive layers of insulation. The 1.6 in thick layer in contact with the pipe is asbestos which is covered with a 1.4 inch thickness of magnesia insulation. The internal pipe diameter is 3 in, the pipewall thickness is 0.40 in made from common brick. The steam temperature is 850ºF, and the internal surface film coefficient is 50 Btu/hr.ft².F, while the ambient outer temperature is 105°F and the outer surface film coefficient is 3.0 Btu/hr.ft².F. Calculate the following: a. value of U based upon the external area of the magnesia covering, Btu/hr.ft2.F b. heat loss from the steam for a length of 190 feet of pipe, Btu/hr
Calculate the quantity of heat conducted per minute through a duralumin circular disc 143 mm diameter and 46 mm thick when the temperature across the thickness of the plate is 10 ℃. Take the coefficient of thermal conductivity of duralumin as 33,000 Btu/hr-ft-R.
QUESTION 3 A steel pipe 150mm external diameter conveys steam at a temperature of 260°C and is covered by two layers of lagging, each 50mm thick. The thermal conductivity coefficient of the inside layer of lagging is 0.0865W/mK while that of the outside layer is 0.0952W/mK. The outside surface temperature of the steel pipe can be taken as being the same temperature of the steam. The ambient temperature is 27°C and the heat transfer coefficient of the outside surface is 15W/m2K. Calculate: 3.1 the heat lost/hr for a pipe length of 30m;
Furnace walls are lined by 3 layers: firebrick with a thickness of 6 in (k=0.95 Btu/h.ft. F), insulating brick (k-0.4 Btu/h.ft.°F) and common brick (k=0.8 Btu /h.ft.°F) Firebrick inlet temperature, T₁ = 1800°F, maximum insulating brick temperature, T₂ = 1720°F and T3 = 280°F. 1. Calculate the thickness of the insulating brick layer. 2. If the common brick is 9 in, calculate the exit temperature.
A pipe of length L connects to thermal reservoirs that are kept constant at temperatures T₁ and T₂. The pipe contains a gas with a thermal conductivity K, a density p, and a heat capacity cp. What is the temperature T of the gas in the tube at a distance x = 0.2L away from the thermal reservoir with temperature T₁ ? Select one: a. b. T = 0.5(T₁+T₂) T = T₁ +0.2 (T₂-T₁) c. T = T₁ +0.2(T₂-T₁) d. T = T₁ +0.2(T₁ - T₂)
You are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…