A steady flow of steam enters a turbine with a specific enthalpy of 2200 kJ/kg and at negligible velocity. It leaves at a low pressur with a specific enthalpy of 1900 kJ/kg also with negligible velocity. The turbine is adiabatic and both inlet and exit pipes are at th same height. If the mass flow rate of steam is 2 kg/s then the power output from the turbine is? Select one: О а. 200kW O b. 500kW О с. 300kw O d. 600kW e. 400kW

A steady flow of steam enters a turbine with a specific enthalpy of 2200 kJ/kg and at negligible velocity. It leaves at a low pressur with a specific enthalpy of 1900 kJ/kg also with negligible velocity. The turbine is adiabatic and both inlet and exit pipes are at th same height. If the mass flow rate of steam is 2 kg/s then the power output from the turbine is? Select one: О а. 200kW O b. 500kW О с. 300kw O d. 600kW e. 400kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
17. A fully inflated tire has a volume of 15 ft3. The pressure and temperature of theair in the tire are 65 psia and 75 F, respectively. At this condition, the air intakeneedle is depressed for 3 s and then released. Treating air as an ideal gas and assumingsmall changes in the tire temperature and volume, Find the amount of air that leftthe tire. Assume a discharge coefficient of 0.61 and a flow area of 0.01 in2.
In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low velocity. If the nozzle outlets are exposed to atmospheric pressure of 100 kPa. Using Bernoulli equation, determine the maximum velocity to which watercan be accelerated by the nozzles before striking the turbinebuckets.
Refrigerant R-134a enters to the compressor of a refrigeration machine at a pressure of 140 kPa and a temperature of -10 °C, then comes out at a pressure of 1 MPa . Volumetric flow of the refrigerant entering the compressor 0.23 m3 /minute. Refrigerant enters throttling valve at 0.95 MPa pressure and 30 °C, and comes out the evaporator at -18 °C as saturated steam. Adiabatic efficiency of the compressor It is 78%. Show the cycle in the T-s diagram. Then calculate: a) Power required to run the compressor b) The heat withdrawn from the cooled environment in unit time, COPsm=? c)Between the evaporator and the compressor, pressure drop of the refrigerant and its heat gain.
Problem 3. Consider a shower that mixes hot and cold saturated liquid water to maintain a steady stream of water at 45 °C. The cold water is supplied at 10 °C and the hot water is supplied at 60 °C. Assume the heat loss from the shower/pipes is negligible (adiabatic). Determine the ratio y of the mass flow rates of the hot and cold water, y = mhot/mcold Cold water T-elbow Hot water
Q1/ Determine the exit velocity of Air enters a diffuser at (80 kPa, 27°C) and (440 m/s) with a flow rate of (5 kg/s) and leaves the diffuser at (42°C). The exit cross section area of the diffuser is (800 cm2). T = 27°C = 300K T2 = 42°C = 315K - h = 300.19 kl/kg - h2 = 315.27 k]/kg
A gas flows steadily through a rotary compressor at a temperature of 16 ⁰C, a pressure of 100kPa, and an enthalpy of 392.2 kJkg-1. The gas leaves the compressor at a temperature of 245⁰C, a pressure of 0.6 MPa and an enthalpy of 534.5 kJkg-1. There is no heat transfer to or fromthe gas as it flows through the compressor. Using the steady flow equation appropriate toeach case, evaluate the external work done per unit mass of gas: a) when the inlet and exit velocities of the gas are negligible b) when the inlet velocity of the gas is 80 ms-1 and the exit velocity of the gas is 160 ms-1.
Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 150W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions.Calculate the total rate of entropy production in
The air considered as the ideal gas flows through the compressor and heat exchanger at a volumetric flow rate of 26.91 m3 / min as shown in the figure. At the same time, a stream of liquid water passes through the heat exchanger. The information given in the figure is for continuous flow. Considering the compressor and heat exchanger as adiabatic and ignoring kinetic and potential energy changes, a) the power requirement of the compressor (kW) and the mass flow rate of the cooling water (kg / h),b) Calculate the entropy generation (kW / K) per unit time for the compressor and heat exchanger.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
A steam turbine is used to test a large pump. The inlet temperature and pressure of the turbine are 4 MPa and 300 C. The turbine exhausts into the ambient air. Turbine has an efficiency of 90%. The pump pressurizes 20 C water from 1 atm to 10 am and its efficiency is 90%. The water flow rate is 50 kg/min. A - Calculate the power input into the pump B - Determine the exit temperature of the turbine. C- Calculate the mass flow rate of steam through the turbine.
Steam enters a turbine with a pressure and temperature of 15 MPa and 650°C, respectively, and leaves as saturated vapour at 100 kPa. The cross-sectional area at the turbine inlet and exit are 0.045 m² and 0.31 m², respectively. The steam flows steadily through the turbine with a mass flow rate of 30 kg/s. i) Sketch the schematic diagram of the turbine and label all parameters given. ii) Calculate the velocity of the steam at inlet, (m/s). iii) Determine the velocity of the steam at exit, (m/s). iv) Calculate the power produced (MW). v) State any assumptions made.