=A standard penetration test is carried out in sand where the efficiency of the hammer n50%. If the measured N-value at 7.5 m depth is 20, find Noo and (N₁)60. The unit weight of the sand is= 15 MR= 1 and18.08 kN/m³. Assume ¹= 0.95. If you know that:ns

nH = 50%N = 20 = 18.08 kN/m3 nB = 1ns = 1nR = 0.95

A standard penetration test is carried out in sand where the efficiency of the hammer ₁ 50%. If the measured N-value at 7.5 m depth is 20, find Neo and (N₁)so. The unit weight of the sand is 18.08 kN/m³. Assume n = 1 and = 15 1R = 0.95. If you know that: ns = 15 mR

A standard penetration test is carried out in sand where the efficiency of the hammer ₁ 50%. If the measured N-value at 7.5 m depth is 20, find Neo and (N₁)so. The unit weight of the sand is 18.08 kN/m³. Assume n = 1 and = 15 1R = 0.95. If you know that: ns = 15 mR

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter3: Natural Soil Deposits And Subsoil Exploration

Section: Chapter Questions

Problem 3.19P

See similar textbooks

Similar questions

In a standard penetration test in sands, the blow count measured at 14 m depth was 26. An automatic hammer released by a trip with an efficiency of 70% was used in the test. The unit weight of sand is 17.5 kN/m³. Determine: (a) N60 (N1) 60 using Peck, Hanson, and Thornburn (1974) correlation with Pa = 100 kPa. The most likely value of the friction angle (not the range). The possible range of relative density per Peck et al. (1974) The Young's Modulus. The table below presents two correlations proposed for estimating Young's Modulus. kg Leonards (1986) E .cm² E (kPa): = 8N60 = aPa (kPa)N60 Kulhawy & Mayne (1990) In the table a = 5 for fine sands, 10 for clean normally consolidated sands, and 15 for clean over consolidated sands. If a specific method is not specified, you may use any possible correlations. While doing so, you must clearly indicate which correlation was used.
Q # 3. Following data are given for a direct shear test conducted on dry sand: Specimen dimensions: 63 mm x63 mm and 25 mm (height). Normal stress: 105 kN/m?. Shear force at failure: 300 N a. Determine the angle of friction, for a normal stress of 180 kN/m?. b. What shear force is required to cause failure?
A very long steel drill pipe got stuck in hard clay at an unknown depth. The drill pipe was applied a large upward force and observed that the drill pipe came out elastically by 500 mm. It was also observed that there was elongation of 0.04 mm in a gauge length of 200 mm. Estimate the depth of hard clay bed. Following consideration may be taken into account: Resistance offered by all material/elements may be taken as zero.
The angle of friction of a compacted dry sand is 37 degrees. In a direct shear test on the sand, anormal stress of 150 kN/m^2 was applied. The size of the specimen was 50mmx50mx30mm(height) SITUATION 1 a. Compute the shearing stress Your answer b. What shear force will cause shear failure? Your answer c. Determine the shear stress at a depth of 3m if the void ratio of the soil is 0.60. Gs Of sand is 2.70
Q # 3. Following data are given for a direct shear test conducted on dry sand: Specimen dimensions: 63 mm × 63 mm and 25 mm (height). Normal stress: 105 kN/m². Shear force at failure: 300 N Determine the angle of friction, for a normal stress of 180 kN/m². b. What shear force is required to cause failure? а.
a) Following results are obtained in a series of CU triaxial tests on saturated samples of a clay. Calculate the effective shear strength parameters (c' and ') and plotting the Mohr- Coulomb failure envelope. (Hint: you can first plot the top points of the circles in q=(01-03)/2 vs. p=(₁03)/2 space.) Test number Confining (cell) Pressure (kPa) Deviator stress (01-03) (kPa) Pore pressure before shear (kPa) Pore water pressure at failure (kPa) ● 1 400 120 300 320 2 400 210 200 260 3 550 270 250 235 b) If we carry out a consolidated drained triaxial test on a specimen taken from the same clay (assume same c', '), what would be the deviator force at failure in a specimen that is consolidated under an isotropic stress of 240 kPa and pore pressure of 300 kPa. The specimen was initially 5 cm in diameter and 10 cm in height. Peak strength (i.e. failure) is reached at axial strain of 4% and volumetric strain of 2% in compression. Hints: the pore pressure is initial pore water pressure
SITUATION 5: A sand sample is subjected to direct shear testing at it's (in - situ) water content. Two tests are performed. For one of the tests, the sample shears at a stress of 400 kPa when the normal stress is 600 kPa. From these data, 15. Determine the value of the apparent cohesion. c. 230 kPa d. 221 kPa а. 100 kPa b. 179 КРа 16. Determine the corresponding angle of internal friction. a. 22.65 degrees b. 26.57 degrees c. 32.54 degrees d. 18.43 degrees
(b) An oedometer test on a specimen of fully saturated stiff clay gave the following results in Table 1 for the pressure increment from 100 kN/m2 to 200 kN/m?. The initial thickness of the specimen under no pressure was 19 mm. Determine my, cy and k using Taylor's Method.
A dilatometer test was conducted in a clay deposit. The groundwater table was locatedat a depth of 3 m below the surface. At a depth of 8 m below the surface, the contact pressure spod was 280 kN/m2 and the expansion stress sp1d was 350 kN/m2. Determinethe following:a. Coefficient of at-rest earth pressure, Kob. Overconsolidation ratio, OCRc. Modulus of elasticity, EsAssume s 9o at a depth of 8 m to be 95 kN/m2 and ms 5 0.35.
7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.
Problem 3) Shown below is a cross-section through a soil layer. A Shelby tube sample was taken from a depth of 25 ft. The sample was extruded in a laboratory, thus subjected to zero total stress. Assume Ko = 0.5 and Ā = -0.1, determine the effective stress on the sample after extrusion. Use the basic Skempton (1954) and Ladd and Lambe (1963) approach to determine the change in pore pressure.
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the bottom the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. Provide Diagram a.709.5 b.177.38 c.88.69 d.354.75