A square plate O-P-Q-R of a linear elastic material with sides 1.0 m is loaded in a state of plane stress. Under a given stress condition, the plate deforms to a new configuration O-P'-Q'-R' as shown in figure (not to scale). Under the given deformation the edges of the plate remain straight. 10 mm y4 R'. 10 mm Q R AP' 10 mm P 20 mm The horizontal displacement of the point (0.5 m, 0.5 mm) in the plate O-P-Q-R (in mm, round off to one decimal place) is

A square plate O-P-Q-R of a linear elastic material with sides 1.0 m is loaded in a state of plane stress. Under a given stress condition, the plate deforms to a new configuration O-P'-Q'-R' as shown in figure (not to scale). Under the given deformation the edges of the plate remain straight. 10 mm y4 R'. 10 mm Q R AP' 10 mm P 20 mm The horizontal displacement of the point (0.5 m, 0.5 mm) in the plate O-P-Q-R (in mm, round off to one decimal place) is

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C dy 40 kN -dr 30 kN
a. At a point in a given material the three dimensional state of stress is given by ox = oy oz = 10 MPa ,Txy F 20 MPa, Tyz = %3D !! TXZ = 10 MPa. Compute the principle planes if the corresponding principles stresses are, ol = 37.3 MPa, c2 = 10MPA, o3 =2.7 MPa %3D %3D b. , What no
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
The aluminum rod AD (E=73 GPa, a=23x10-6/°C) has a diameter of 15 mm and is attached to the rigid support at A when the temperature T1 = 30°C. If the temperature becomes T2 = -20°C, and the axial loads are applied to the rod as shown, determine: a) The location and magnitude of the maximum stress acting on the rod AD b) Displacement of point D c) Average strain in part BC 5 kN A +7 kN - 5 kN в C D 1400 mm- 1300 mm- 1500 mm-
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
A critical point in a part made of a ductile material is subject to the following state of plane stress: 15ksi, 30 ksi, 15 ksi, Ox,min = -35 ksi, Oy,min = 30 ksi, Txy,min = -15 ksi. Ох,max бу,max Тxy,max %3D There are no stress concentrations. The load line is propositional. The material has a yield strength of Sy = 130 ksi, an ultimate strength of Su = 200 ksi, and a fully corrected endurance limit of Sn : 75 ksi. Calculate the: (a) Static factor of safety using the MSSTF, (b) Static factor of safety using the DETF, (c) Fatigue factor of safety using the Soderberg criterion, (d) Fatigue factor of safety using the Goodman criterion, (e) Fatigue factor of safety using the ASME elliptic criterion.