A single-phase half--bridge inverter is connected to a 600V d.c. source. A series connected R-L load has R = 60 ohm, L = 70mH. The inverter frequency is 60Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 11th harmonic.

A single-phase half--bridge inverter is connected to a 600V d.c. source. A series connected R-L load has R = 60 ohm, L = 70mH. The inverter frequency is 60Hz. Determine the values of the rms load current, the load power and the total harmonic distortion factor, up to the 11th harmonic.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as the supply voltage. Show the circuit and resistor values. Indicate the value of ID. Indicate the value of VGS. Indicate the value of VDS.
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
2. A transformer-coupled class A amplifier drives an 8-ohm speaker through a 4:1 transformer. Using a power supply of Vcc = 36 V, the circuit delivers 3 W to the load. a. Calculate the following: i. Piecj across transformer primary. ii. Vuscd- ii. Vjac) at transformer primary. iv. The rms values of load and primary current. b. Draw the circuit diagram of a class A transformer-coupled amplifier using an npn transistor.
Please written by computer Answer the following questions:a. Name a suitable topology that can be used in the above DC/DC converters to achieve the required regulation with the minimum provided efficiency.b. Calculate the efficiency of the linear regulator.c. Calculate the total input power and the input current.d. Calculate the overall efficiency of the system.e. If a 100uF capacitor is used at the input to minimize the ripple. Assume the rise time of the input source is 0.2ms. Estimate the maximum inrush current to charge the capacitor to 12V.
FET: Plot the plot the AC & DC load line and Find the Q point. IDSS = 5 mA VGSOFF = - 5V
Draw the block diagram of a HVDC converter station and briefly describe the function of each Component.Define LCC and VSC and compare their performance
Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vot Vm = 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip = 0.1 V (assume ideal diodes) T=0.01 sec. tisec) Q3) V in Design a regulated circuit to supply a constant voltage of (10 V) across a resistive load of (50 2). The input voltage is shown in the figure. The minimum current for the Zener diode operation is (Izk=5mA). Find the 15 V 15 maximum power dissipated in the Zener diode. 12.5 12 V 10
Find full load current..
3. A single-phase to single-phase cycloconverter "bridge type" with input voltage and frequency 150V and 50Hz. respectively. The output frequency is 10Hz and the firing angle equal to 45°. The load is resistance with the value of 1002 in series with reactive inductance of the value of 20mH. Assume the extinction angle equal 180°. a. Draw the waveforms output voltage, output current, source current, the thyristors currents (iT, IT, IT and in) b. Calculate the rms of output voltage. c. The rms current of each thyristor. d. The input power factor
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
Explain the working of single phase full converter for RLE load discontinous mode o operation with neat sketch, waveform and equations.
Find the performance parameters (FF, RF and n) for the Single phase bridge uncontrolled rectifier with RL load. If the phase voltage: Vph(t) = Vm sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms.