A single-phase full-wave rectifier produces a fix output Vo(avg) = 197 V from an AC (a) source of Vpeak = 311 V and frequency of 50 Hz. As an engineer working in “Ababa Electric Sdn. Bhd.", you are required to modified the switches such it produces a variable output Vo(avg)= 99V ~ 197V. Proposed the required switches to allow the full-wave rectifier to produce a variable output voltages. Sketch the overall setup for the new system.

A single-phase full-wave rectifier produces a fix output Vo(avg) = 197 V from an AC (a) source of Vpeak = 311 V and frequency of 50 Hz. As an engineer working in “Ababa Electric Sdn. Bhd.", you are required to modified the switches such it produces a variable output Vo(avg)= 99V ~ 197V. Proposed the required switches to allow the full-wave rectifier to produce a variable output voltages. Sketch the overall setup for the new system.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

What is CEMF?
What is the difference between a diode and rectifier?
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
4. The circuits parameters for an uncontrolled full-wave rectifier are as follows: Vin rms = 20V w= 314,159 rad/s Rload = 1KQ All diodes are Silisium and the equivalent circuit given below will be used. VFT = 0.7V, Ron = 0.01Q VET Ron + a) Find the value of DC voltage of the RL load resistance. b) Find the required rated PIV values for each diodes. c) Find the maximum conduction current of the diodes. d) Plot waveforms of the output current and voltage values.
Note: Answer All question 1: A) For a single-phase half-wave uncontrolled rectifier with (RL) load, find the rms value of the output voltage (V) and form factor (FF%) with supply voltage: v,(t) = 10 sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms. The conduction angle B = 220°. %3D
Three Phase Half-Wave Fully Controlled Rectifier when pure Resistive and highly Inductive loads are connected: i. Draw graphs when α = 120, 150 degrees. ii. Derive the output average voltage. iii. Derive the output rms voltage.
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 162 V and the firing angle of the SCR is 60 degrees, the peak voltage of the input sinusoidal would be: O A. 197 V O B. 228 V O C. Can't tell; need more information. O D. 340 V O E. None of the other choices are correct
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Three Phase Full-Wave Fully Controlled Rectifier when highly Inductive load is connected: i. Draw graphs when α = 30, 60, 90, 120, 150 degrees. ii. Derive the output average voltage. iii. Derive the output rms voltage.
5- The frequency of the output voltage obtained from three-phase Wye/Delta connected rectifier is :* 6 times the rated source frequency. 3 times the rated source frequency 2 times the rated source frequency
Question 2) A full-wave rectifier with ohmic load given in the figure below feeds a 75 Q load and the effective (rms) value of the source voltage is 220V, its frequency is 50 Hz. Accordingly, find the following desired circuit parameters: a) the peak voltage of the source, b) the peak current of the load, c) Average stress of the load, d) Average current of the load, e) The effective (rms) voltage of the load, f) Effective (rms) current of the load, g) Power of the load i D2 vs R
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode