Answered: A single-phase, 60-Hz supply is…

A single-phase, 60-Hz supply is connected to a load consisting of a 100 Ω resistor in parallel with a 50-µF capacitor. Find the source power factor. (Make sure to indicate leading or lagging PF)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Power factor is 0.707 when three-phase inductive 250 kW power is drawn from 440 V transmission line.…

A: According to the question we have to find the current and power factor drawn from the line.

Q: A 3Ø, 2000KW, 480V A-connected alternator is short-circuited and is operated at rate speed to…

A: Delta Connection: A delta connection is made up of three passive components that are either the same…

Q: A three-phase motor draws 9 kVA at a lagging PF of 0.8 from a balanced system with line voltages of…

Q: Three-Phase System Three loads are connected in parallel to a 12.47 kV, 60 Hz three-phase supply.…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Three parallel single phase loads are supplied from 240V rms, 60 Hz single phase source. The loads…

A: Given data: VS=240 V RMSf=60 Hzpf1=0.6 lagP1=24 hpR2=6 ΩQ3=24 kVARpf3=0.6 lead

Q: The power consumption of a factory is 2000 kVA at 0.6 pf lagging. A synchronous motor is added to…

A: Given Load P1=2000 KVA at pf1= 0.6 power factor Load P2 =850 KVA at pf2 power factor Overall…

Q: A small installation consists of the following loads connected in parallel across a single-phase…

A: When the devices are connected in parallel, the potential difference across all the elements is…

Q: Given a star connected system with power factor of 80 percent, true power of 2,500 kW and phase…

Q: 1. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and…

Q: 3 A load draws 20 KVA at power Factor OF 0.75 lagging From a 120 VRMS sinu suidal source. Calculate…

Q: A source supplies power to the following three loads connected in par- allel: (1) a lighting load…

A: The solution is given below

Q: 43. A series circuit consisting of a 50-ohm resistor, 0.5-henry inductor and a 100-microfarad…

A: In this question, RLC are connected in the series. Apperent power S= VI* We know S= P+jQ Where Q…

Q: 6. If a power system has 10,000 kVA capacity, operating at 0.7 lagging power factor and cost of…

A: consider the given question 6.

Q: A 60-Hz, single-phase source with V = 277/30° volts is applied to a circuit el (a) Determine the…

Q: Problem 11.6: Determine the capacitor rating in KVAR and also in farad to improve the load pf from…

A: Given: A power factor of the load is improved from 0.75 lagging to 0.95 lagging in a 3-phase, 60 Hz,…

Q: series circuit containing a noninductive resistance of 3 Ω and a coil is connected to a 120 V, 60 Hz…

Q: If a load absord 20KVA at the leading power factor of 0.6 Write the complex form of power

Q: A 400V, 60HZ, three-phase star-con supplies a delta-connected load, each phase of which has a…

A: Given data f=60 HzVL=400VRph=30 ohmLph=40 mHXLph=2×3.14×60×30×10-3=11.30 ohmrline=2.20 ohm…

Q: A balanced three-phase A-connected supply delivers power through a three-phase wire in an industrial…

A: NOTE: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A circuit is composed of a resistance of 22 ohms, an inductance of 0.11 henry and a capacitance of…

Q: PROBLEMS : A 130- v OLT 50-CYCLE S OURCE CONNECTED TO SERIES CKT. CONSISTING OF A 402 RESISTOR AND…

Q: A load of 500 kVA operates at 0.6 lagging power factor on 1100V, 50 Hz mains. The power factor of…

Q: Q 4/ A 3000 kVA, 3-phase, star-connected, 50 Hz, 2800 V alternator has resistance 0.120. A field…

Q: Three loads connected in parallel across a 1000-V (RMS), 60-Hz single-phase source. Load 1:…

Q: 7. A system operates at 220 kVA and 11 kV. Using these quantities as base values, find the base…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: A small installation consists of the following loads connected in parallel across a single-phase…

A: In this question , we will find total current , total active power, total apparent power and power…

Q: A 230 V, 50 Hz power source is connected to the some loads, where: • Load-1: R = 4.5 Q and in series…

A: 3 loads are connected with 230V 50Hz supply. Complex power S= VI* Where I* is conjugate of the…

Q: Solve for the equivalent impedance and admittance seen at the source. Solve for is(t).

Q: Supplementary Problems: 1. An impedance (6 + j8) is connected across 200-V, 50 Hz mains in parallel…

Q: 1. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and…

A: Calculate the initial power factor of the circuit. Ps=VIcosϕcosϕ=PsVI=450×103 W2.5×103 V215 A=0.837

Q: QI: A synchronous motor having a power consumption of 50 kW is connected in parallel with a load of…

A: In this question we have given parallel connected load and combined power factor....We have to find…

Q: Please answer quickly "In series-connected ac circuit, the total voltage across the circuit is…

A: In this question we will write circuit problems...

Q: Q5: Three-phase, 50 Hz, 132 KV power system of equivalent impedance 10+j35 Q with load 110+j29 Q.…

Q: Problem 4 An electric saw, a wood shaper, and a motor load of a workshop establish a 18 kVA power…

Q: 1. A factory takes the following balanced loads from a 440-V, 1-phase, 50-Hz supply: (i) a lighting…

A: Here welding load and motor load both are same P1=30K×cos∅=30K×.5=15KW…

Q: Consider a building with a real power demand of 650 kW and reactive power demand of 480 KVAR.…

A: In building Power demand 650KW Reactive power 480KVAR The power factor? Capacitor rating to be…

Q: A source with 240 Vms, 50 Hz is connected in parallel to the three loads. These loads can be…

A: In this question we will find total load ,power factor and capacitance value for improving power…

Q: For the circuit shown in the following figure, a) Find and draw the Thévenin equivalent circuit at…

A: Given that Electrical network as follows

Q: II. Problem Solving A 400 resistor is connected in parallel to a coil having a resistance of 10 and…

Q: Q2) A three phase load (motor) draws 30 kW when connected to 440 V rms, 50 Hz line if the power…

Q: 2. A 400-V, 3-phase induction motor load takes 900 kVA at a power factor of 0.707. Calculate the kVA…

A: Case I S= 900 KVA PF1= 0.707 PF1 = cos ϕ1 = 0.707 Φ1= 45° Real power P1 = S * PF1 = 900k * 0.707 =…

Q: 5. Three impedances of (1+j5)N, (1+j12)N and (2+j3)N are connected in star to a 3-0 system with line…

Q: A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a…

Q: Q5: Three-phase, 50 Hz, 132 KV power system of equivalent impedance 10+j35 N with load 110+j29 Q.…

Q: A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of…

A: voltage =240 volts p.f. of 0.75 lagging.

Q: Given a mesh connected system with reactive factor of 60 percent, true power of 2,500 kW and phase…

A: A network in which devices or nodes are linked together, branching off other devices or nodes known…

Q: A single-phase motor is connected as shown inFigure to a 50-Hz network. The capacitor valueis chosen…

A: The circuit of the single-phase motor is shown below: The unit power factor means that the phase…

Q: An AC series circuit has R= 300N, L = 0.90H, and C = 2.0µF with a generator of 50V and w = 1000…

Q: An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance…

A: Given ZL=11.5+j10 ΩZC=8-j20 Ω circuit diagram is

Question

A single-phase, 60-Hz supply is connected to a load consisting of a 100 Ω resistor in parallel with a 50-µF capacitor. Find the source power factor. (Make sure to indicate leading or lagging PF)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
Question 3 To reduce the power consumption, the capacitors Complete should be located Marked out of 1.00 O a. As far as possible to the load P Flag question b. Not suitable place O c. As close as possible to the load d. Not too close not too far from the load Question 4 A load 200+j0 ohms is connected across a 250 V and Complete 50 Hz supply. Find the reactive power. Marked out of 1.00 O a. 350 VAR P Flag question O b. 360 VAR O C. zero VAR Od. 420 VAR
A Star 3Phase source with phase voltage of 400V at 50HZ is connected to a delta connected 3Phase AC Motor. The transmisson line resistance from source to load terminal is 1 Ohm. The internal resistance of each winding of motor is 9 Ohm and the inductance of each coil is 38.2 mH. What is the true power delivered to load? O A) 13099 B) 14999 O C) 15099 O D) None
A 2.5A current is flowing in a series circuit comprises of a coil with inductance 15mH and resistance 102 and a variable capacitor. The supply voltage is 120V at 60 Hz. Estimate the following: i. The capacitance and impedance. ii. Angle between supply voltage and current. ii. The reactive power consumed
In case RL load, it is desired to get an average load voltage of 75 V. Determine the firing angle if the ac supply voltage is 200V per phase. If the load resistance is 302, calculate the average load current and power. Design the thyristor. 4-
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
4. Design the network in the figure to have the following characteristics: i. BW - 500 Hz ii. Qp = 30 iii. Vemax = 1.8 V 0.2 mA Z0° C7 R, = 0 N
A 3-phase, 50 Hz, 1100 V motor has a total load output of 100 hp and a power factor of 0.78 learning and an efficiency of 85 %. This power factor is corrected to 0.92 by a capacitor bank connected in delta. A capacitance unit is made up of 4 identical 275 V capacitors. So find the capacitance of each capacitor.