A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam), a uniform service live load of 2.0 kips/ft, and a concentrated service dead load of 40 kips. The beam is 40 feet long, and the concentrated load is located 15 feet from the left end. The beam has continuous lateral support, and A572 Grade 50 steel is used. Is a W30 × 108 adequate? a. Use LRFD. b. Use ASD. Pp = 40 k 15'- 25'- Wp = 1.0 k/ft WL = 2.0 k/ft W30 X 108 40'-

A simply supported beam is subjected to a uniform service dead load of 1.0 kips/ft (including the weight of the beam), a uniform service live load of 2.0 kips/ft, and a concentrated service dead load of 40 kips. The beam is 40 feet long, and the concentrated load is located 15 feet from the left end. The beam has continuous lateral support, and A572 Grade 50 steel is used. Is a W30 × 108 adequate? a. Use LRFD. b. Use ASD. Pp = 40 k 15'- 25'- Wp = 1.0 k/ft WL = 2.0 k/ft W30 X 108 40'-

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.3P

See similar textbooks

Similar questions

Use 2015 NSCP A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft(including the weight of the beam) a uniform service live load of 2.0 kips/ft and a concentrated service dead load of 40 kips. The beam is 40ft long and a concentrated load is located 15 ft from the left end. The beam has continuous lateral support and A36 steel is used. Is W30x108 adequate? a) Use LRFD b) use ASD P₁=40* -15- 25'- WD = 1.0km W₁ = 2.0³m W30 x 108 40'-
5.5-3 A simplrted beam is subjected to a uniform service dead load of 1.0 kip cluding the weight of the beam), a uniform service live load of 0 kipft, and a concentrated service dead load of 40 kips. The beam feet long, and the concentrated load is located 15 feet from the left The beam has continuous lateral support, and A572 Grade 50 steel is used. Is a W30 x 108 adequate a. Use LRFD. b. Use ASD.
A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
An 80-foot long plate girder (see below) is fabricated from a ½-inch x 78-inch web and two 3inch x 22-inch flanges. Continuous lateral support is provided. The steel is A992. The loading consists of a uniform service dead load of 1.0 kip/ft (including the self-weight), a uniform service live load of 2.0 kips/ft, and a concentrated service live load of 500 kips at midspan. Stiffeners are placed at each end and at 4 feet, 16 feet, and 28 feet from each end. Once stiffener is placed at midspan. Determine whether the flexural strength is adequate using LRFD.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
Q2 1- Check the following weather one way or two way 2- Calculate the design ultimate load Wu on the on the beams B3, B6 Assume slab load: Live load = 5 kN/m2 Dead load = 8 kN/m? Beam size 300x500 mm %3D B5 B6 B7 3.6 m |L 4.8 4 m 5m 5m BI B2 B4
The beam under the Live and Dead loads is shown below. The steel class is $235. Lig L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3
1. Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E345 MPa and Fu= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. IR₁ 0.90m 70,KN * W14 x 68 1.20m 70 KN * 0.90m R₂ W14x68 70 KN
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
PROBLEM 4: The beam shown the figure below is a W16x31 of A992 steel and has continuous lat- eral support. The two concentrated loads are service live loads. Neglect the weight of the beam and determine whether the beam is adequate. a. Use LRFD. b. Use ASD. 60k 60k W16 x 31 asap +4
A simply supported A992 W14x61 30-foot length beam has a concentrated load, P, and it’s midspan. P is a service live load. What is the maximum permissible value of P. Use LRFD, then use ASD. You can assume that the beam has continuous lateral support. Manually verify that the beam is compact. Don’t forget to account for self-weight