A shop crane consists of a boom AC that is supported by a pin at A and by a rectangular tension bar BD, as shown in Fig. 1.1. Details of the pin joints at A and B are shown in Views a-a and b- b, respectively. The tension bar BD has a width w = 1.5 in. and a thickness t = 0.5 in. If the vertical load at C is P = 5 kips, then determine the following: 1. What is the calculated normal stress ? in the bar BD. 2. Determine the calculated shear stress? at pins A, B, and D. Assume that the pins are 3/4" in diameter. 4 ft Ja 6 ft 5 P=5 kips View b-b View a-a Figure 1.1 Shop Crane

A shop crane consists of a boom AC that is supported by a pin at A and by a rectangular tension bar BD, as shown in Fig. 1.1. Details of the pin joints at A and B are shown in Views a-a and b- b, respectively. The tension bar BD has a width w = 1.5 in. and a thickness t = 0.5 in. If the vertical load at C is P = 5 kips, then determine the following: 1. What is the calculated normal stress ? in the bar BD. 2. Determine the calculated shear stress? at pins A, B, and D. Assume that the pins are 3/4" in diameter. 4 ft Ja 6 ft 5 P=5 kips View b-b View a-a Figure 1.1 Shop Crane

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the truss structure and the loading given below. a) Compute the average axial stress on member AB, b) compute the average shear stress at the pin of connection A. d- 20 mm 600 mm 50 mm -S00 mm 60 kN 25 mm | I 20 mm 30 mm I20 mm 25 mm TOP VIEW OF MEMBER AB d = 30 mm
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
AT-section is the cross section of a loaded beam as shown. Given: U1-32 kN/m; M1 = 100 kN-m; P1=120 kN a.) Draw the shear diagram using graphical solution b.) Determine maximum shearing stress. c.) Determine the shearing stress at the junction of the T-section. 200 mm 32 M- 100 P-120 16 ト 4"L 6 m) 20 mm CS Scanned with CamScanner 100 mm ww Os
4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN
For the portal frame shown in the given figure, the shear equation is B 4 m (a) (b) (c) (d) P MBC + MCB 4 4 m MBA + MAB. 4 MCD 4 MATT El MBA+MAB + P = 0 4 + P = 0 + Constant 4 m hinge +P=0 C MCD 4 LID mim + P = 0
0.25 m 0.25 m DRA E 60° 1.5 m F D 10° 30° H L 0.5 m K G 2m J HW18: FBD of the bucket and whole upper assembly up to EF to find force in EF and reactions at H. Then draw a FBD of CDEH to find force in AD. AD can also be found from the FBD of the entire upper crane up to CD. Draw a FBD of the bucket to find the force at K and J. The shovel load acting at G is 1.25Mg. Answer: FEF=8.18kN, FAD=158 kN
lho H.W.2: 1,200 mm The load P produces an axial strain of -1,800 pe in post (2). Determine the axial strain in rod (1). (1) rigid plate 480 mm bare 1.5 mm 600 7. 100000\ 300 mm 300 mm 600 mm (2) S. 1,0 8 11 2,09 4 1, nd supported by two rods at A and- E naliad After load Pis applie
105° SIMPLE 50° STRESSES 65° 60 KN 1. Two steel bars are 15° BLOCK E connected by two 20 mm 80 mm 50 KN steel bolts. Each steel bar has WALL BLOCK A 200 mm a width of 80 mm, length of 200 mm and thickness of 20 mm. Steel Bar 1 is rigidly 20 mm BOLT attached to cable DG and Steel Bar 2 is rigidly attached to a steel wall. STEEL BAR 2 the maximum axial stress of the STEEL BAR 1 steel bar. CABLE DG
STRUCTURAL THEORY Show complete solution for better understanding Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200 GPa. Use the method of Virtual Work F b.-37.5 C.-30 d. 30 -2m- 1. Determine the stress on member AE a. 37.5 E c. 2 d.3 n B 45 KN 2 m 2. How many zero-force member are there? a. 0 b. 1 3. Determine the vertical deflection of joint E a. 1.42 b. 3.38 c. 2.95 d. 1.24 1.5 m
The boom DF of the jib crane and the column DE have a uniform weight of 50 lb/ft. If the supported load is 300 lb, determine the resultant internal loadings in the crane on cross sections at points A, B, and C. 8 ft +3 ft- 5 ft 300 lb
note: SN = 18, to the topload will be 118kN
An overhang beam is loaded as shown below. The beam cross-section was butlt by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t= 9mm Flange Width, B, -112.5 mm Web Thickness, t. -9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,-200 MPa on single shear, a, =260MPa on double shear. 1. determine the location of centroid, ȳ, from top of the beam in mm 2. determine the moment of inertia, I, of the section in mm4 3. determine the maximum allowable moment, Mall, inkn-m, base on the beam's cross section.