a servomechanism is designed to keep radar antenna pounted at flying aeroplane if the aeroplane is flying with the velocity of 600km/hr. The velocity is given at a range of 2km and the maximum tracking error is to be within 0.1\deg .determine the velocity error. Kv/s(1+st)

a servomechanism is designed to keep radar antenna pounted at flying aeroplane if the aeroplane is flying with the velocity of 600km/hr. The velocity is given at a range of 2km and the maximum tracking error is to be within 0.1\deg .determine the velocity error. Kv/s(1+st)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter14: Basic Trigonometry And Vectors

Section: Chapter Questions

Problem 1RQ: 1. Which trigonometric function is used to find the angle if the length of the hypotenuse and of the...

See similar textbooks

Related questions

Q: Review the following statements and select the most appropriate answer.

A: Option C is the correct answer.Explanation:Step 1: Statement 1 is correct because harsh conditions…

Q: Determine the Thevenin Equivalent Circuit (Vth and Rth) for the following circuit diagram

A: Given:we need to find Thevenin equivalent (VTH, RTH) across load in the above circuit.

Q: 3) 75LVE 600 JISOR m 卝 10.02V 40nt од Find the The venin equivalent of the Circuit at a-b term hols

A: The given circuit isWe need to determine the Thevenin's equivalent circuit at the terminals a-b.

Q: Solve the Following Question

A: Below is the clarified and detailed explanation for above tricky question....if you are ok with my…

Q: 12V 240 120 PART-A (CALCULATION) Calculate the current and voltage value of the R_Load (R4) resistor…

Q: stitut LIT appropriate answer. Statement one Due to improvement in health and safety at work. fewer…

A: d) Both statements are correct Explanation:The first statement: "Due to improvement in health and…

Q: Explain how industrial based PLC plays a significant role in automation.

A: Industrial Programmable Logic Controllers (PLCs) play a critical role in automating various…

Q: 2KQ 1VW 4KQ 2V M + 4KQ 4V W 6KQ w (+V) (-V) Vout

A: Determine the output voltage of the Op-amp

Q: I3=? 1₁ =6A IT 13 www 402 w 1202 ww 202 w 40 Ω IT

Q: Consider the circuit shown in the figure below. (Assume R₁ + b = 11.5 and R 2 = 5.50 2.) 25.0 V R₁ a…

A: Nodal analysis uses ohms law and Kirchhoffs current law.The detailed solution is provided below.

Q: 4.2-1 A DSB-SC modulation generates a signal (t) = Aem(1) cos (wet+6). (a) Sketch the amplitude and…

Q: PLS HELP ASAP on both pls I BEG

Q: Determine the prediction model for current at amy time > 0 in an electrical circuit cortaining a…

A: A series RLC circuit havingR=20 Ω.L=10 H.C=0.05 F.The supply voltage isE=60 V.The initial charge in…

Q: . Time shifting and scaling. Given the signal x(t) shown below

A: In the given question we need to plot the given signal.

Q: The ammeter reads 9.04. what is the emf of the battery? 9.0 V 2.0 Ω ww + 3.0 Ω www A ww 1.0 Ω + Hil…

A: Given:with ammeter current 9 A.we need to find: the emf E of battery.

Q: Figure P4.2-10 4.2-10 A slightly modified version of the scrambler in Fig. P4.2-10 was first used…

Q: Assume

A: This is an junction question

Q: Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max)…

A: The objective of this question is to design a shunt linear regulator and determine the power rating…

Q: - Determine IR2 and VR4 for the circuit shown below. Vs -12V Hill R1 ww 560Q 1R2 R3 www 2.2kQ R4 R2…

Q: An electric field in the xy-plane is Ē= -axy-ayx, (volts per unit length). There are two points of…

A: The answer to this question is explained as follows Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Q1) What is current in terms of charge? a) Current is measured 2A in a DC circuit * How much charge…

A: The objective of the question is to understand the concept of electric current in terms of charge…

Q: d) Verify Kirchhoff's current law at a node. e) Determine the power supplied to the circuit. f)…

A: d)Kirchoff's current law (KCL) states that the algebraic sum of branch currents flowing into and out…

Q: Question-3: Sketch the voltage transfer characteristic of the NMOS inverter circuit given in Figure…

A: The output voltage of the NMOS inverter circuit is determined by the on/off state of the NMOS…

Q: 7.6 Calculate the necessary aperture for a parabolic-dish aerial to have a gain of 60 dBi at 5 GHz…

A: Given Data:Required:Here, the aperture area needs to be calculated.

Q: 10 V Determine IL2 in the below figure. L₁ = 4 mH, L3 = 2 mH, f = 4.7 kHz, and IL3 = 20 mA. The…

A: An inductor is an electronic component that stores electrical energy in a magnetic field when…

Q: (a) The electron concentration in a piece of Si at 300 K is 105 cm-³. What is the hole…

A: Note: Since the user has asked for the solution of parts (b), (c), and (d). Thus, we will solve only…

Q: Find the f(t) for the signal shown in the figure below: -2 -1 3 2 0 f(t) 1 Time (t) 2 3 Select one:…

Q: [Q2] Different analog signals are sampled at a rate of 26kHz. The samples from these signals are…

A: The objective of the question is to find out the maximum number of signals that can be transmitted…

Q: c. What is the expression for the bandwidth and the quality factor?

A: The bandwidth and quality factor of the given band reject filter needs to be calculated and the same…

Q: Problem 6.1 Sketch the time domain waveform x(t) and find the Laplace transform X(s) for the…

A: Given dataThe signals are given as,(a) (b) (c) and denotes the unit step.We need to sketch the…

Q: Draw a circuit with a 120 volt ac power source, a switch, and a motor with a resistance of 22 ohms…

A: The voltage, The resistance of motor,

Q: For the circuit shown, (a) what is the resonance frequency? (b) What is the "rms" current and the…

Q: A message source generates ten messages with probabilities 0.1, 0.13, 0.01, 0.04, 0.08, 0.29, 0.06,…

A: Given:Source alphabet and respective probabilities: symbol…

Q: 2. In this problem, we will analyze the energy and power relations for the charging capacitor…

A: Given circuit: -

Q: Q1\ For the RL circuit shown in Fig. 1: a. Write the mathematical expressions for i, and following…

Q: In figure, R3 = R₁ = 5.6k, and R₂ = 220kn. 220ΚΩ. a) If V₁ = 27mV and V2 = 0mV, what is Vout V1 b)…

A: The objective of the question is to calculate the output voltage (Vout) of a differential amplifier…

Q: A 3 meter by 4 meter rectangle is in the xy-plane. At each of three corners there is a charge. At…

A: Electric potential, Vp = -4500 J/CExplanation:

Q: 5. Determine the input impedance to the series network in the figure. Draw the impedance diagram. Z₁…

A: Impedance is a measure of opposition that a circuit presents to the flow of alternating current…

Q: P1) For the unit-sized inverter shown in figure Error! Reference source not found., find…

A: Rise time = 24 nsecFall time is 19.2 nsecExplanation:

Q: ind inverse Fourier Transform

Q: Can you explain how the Binary ripple counter below works, and making minimal changes have it count…

A: According to the question, we need to explain the workings of the binary ripple counter as shown…

Q: Represent the electrical network shown below in state space, where x = [vi]' is the state vector and…

A: In the given electrical circuit the state space equivalent needs to be obtained. The given circuit…

Q: Using Superposition theorem, find the value of V if the current | = 2A 487 48V 492 42 +WW 292 I 892…

A: The given circuit isWe need to determine the value of V if the current I=2 A using superposition…

Q: B-5-24. Consider the servo system with tachometer feedback shown in Figure 5-81. Determine the…

A: Determine the range of stability k and kh and write the inequalities about k and kh

Q: 7. For the circuit below, calculate the value of Zz for maximum average power transfer to the load.…

A: Calculate the value of Z for maximum average power tyansfer to the load. In addition, deternmine the…

Q: a. A single-phase semi-converter supplies an inductive load having an impedance of 3k. Assume that…

A: The objective of the question is to calculate the average output voltage, supply RMS current, and…

Q: 3.16. A 50-cm long wire passes 20 times a second under the pole-face of a square magnet. If each…

A: The EMF induced is Induced emf =Rate of change of magnetic flux…

Q: The supply voltage of the op amp in the circuit is 16 V. If R₁ = 2,3000, assign a resistance value…

A: Given circuit: -Find: -The value of Rf .

Q: using Boolean algebra simplify the following expression (B + B)( BC + BCD') please answer in typing…

Q: A signal x[n] having the DT Fourier Series (DTFS) coefficients Co = 3 C1 = C2 = 5 C3 = 2-j 2+j is…

A: An input signal x[n] having the DT Fourier Series (DTFS) coefficients are given…

Concept explainers

Properties of Radar

Radar stands for radio detection and ranging. It is a type of system which detects the distance, velocity, and angle of objects. This system can also detect weather formations, spacecraft, aircraft, missiles, terrain, etc.

Question

System of detection and tracking of stationary and moving targets.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Given data

VIEW

Step 3: Converting Units and Range

VIEW

Step 4: Calculating Maximum Allowable Tangential Velocity Error

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In an air line, adjacent maxima are found at 12.5 cm and 37.5 cm. The operating fre- quency is (a) 1.5 GHz (b) 600 MHz (c) 300 MHz (d) 1.2 GHz
True or False. If the noise variance increases, the average power density of the Gaussian white noise increases
A 10 MHz carrier is frequency modulated by a sinusoidal signal of 500 Hz frequency and the maximum frequency deviation is 50 KHz. What will be the bandwidth of the FM signal?
The period of this signal is about------ ms (milliseconds). The oscilloscope range selector determines the scale on the screen. That means number of volts per line for amplitude vertical (v/div) and the number of milliseconds per line for time horizontally (ms/div).
A radar transmits a pulse with a power of 50 kW, which is reflected from a target that is20 km away and has a radar cross section of 3 m2. The signal frequency is 20 GHz, and theantenna has a gain of 25 dB.(a) Calculate the power density at the antenna input.(b) Design the radar pulse wave. Assume 20 km is the maximum range and 0.05 duty cycle.
This subject is antenna and wave propagation of ece pls solve neatly and faster thanks
Ope X. The frequency spectrum of an AM signal is shown below: 5.5V 1V 1V 52kHz 58kHz a) if the modulating signal is a sine wave, write the equation of the modulating signal b) if the carrier signal is a cosine wave, write the equation of the carrier signal c) calculate the current of the AM signal flowing through a 300-ohm load
• An X-band CW radar operates at a frequency of 10 GHz and triangularly sweeps a bandwidth of frequency excursion of 2 MHz at a 200 Hz rate. The frequency difference between the transmit and receive signals on the up-sweep is 65.51 kHz and on the down-sweep it is 82.65 kHz. Find the target range and radial velocity.
04] A radar transmits a pulse with a power of 50 kW, which is reflected from a target that is 20 km away and has a radar cross section of 3 m2. The signal frequency is 20 GHz, and the antenna has a gain of 25 dB. (a) Calculate the power density at the antenna input. (b) Design the radar pulse wave. Assume 20 km is the maximum range and 0.05 duty cycle.
Multiple Choice Questions (MCQ): (15 M 1. For a horn antenna, in which flaring is done only in one direction is a) Conical antenna b) Sectoral antenna c) Pyramidal horn antenna d) Exponential horn antenna 2. Wave unaffected by night or day is a) Ground wave b) Skywave c) Space wave d) Tropospheric wave 3. When a wave is incident normally then the acceptable highest frequency at which signal can be returned is the a) critical frequency b) LUF c) optimum frequency d) dominating frequency 4. High frequency range is from? a. 0.3 to 3 MHz b. 3 to 30 MHz c. 30 to 300 MHz d. 3to 30 MHz 5. The actual permittivity of a medium whose relative permittivity is 5. a) 4.43*10-¹1F/m b) 4.43*10-¹2F/m c) 4.43*10¹¹F/m d) 4.43* 10¹2F/m
An X-band CW radar operates at a frequency of 10 GHz and triangularly sweeps a bandwidth of frequencyexcursion of 2 MHz at a 200 Hz rate. The frequency difference between the transmit and receive signalson the up-sweep is 65.51 kHz and on the down-sweep it is 82.65 kHz. Find the target range and radialvelocity.
3) Solve the cutoff frequency for the first mode and second mode of WR975 Wave guide TABLE 7.1 Some Standard Rectangular Waveguides Waveguide de signation a (in) b (in) t (in) fe, (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12–1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2–12.4 WR62 0.622 0.311 0.040 9.49 12.4–18