A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced with four reinforcing bars 3 cm in diameter. It is filled with concrete and supports a load of 800 kN. Bearing plates are placed on top and bottom of the 1.5 m high column to assure equal deformation of the steel and concrete. Find the stress in each material and the change in height of the column. [ Ec= 14 000 MPa, Es=200 GPa assume both column and steel re-bar are same type of steel]

A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced with four reinforcing bars 3 cm in diameter. It is filled with concrete and supports a load of 800 kN. Bearing plates are placed on top and bottom of the 1.5 m high column to assure equal deformation of the steel and concrete. Find the stress in each material and the change in height of the column. [ Ec= 14 000 MPa, Es=200 GPa assume both column and steel re-bar are same type of steel]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation (20 points), o co (20 points), Ost (20 points). |1000 kN Bearing plate 1 a Steel Concrete 300 mm 300 mm Section a-a
The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E = 25 GPa for concrete 900 KN 250 mm 375 mm
Compute the stress at each segment of the pipe.
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
A rectangular reinforced concrete beam is subjected to a service moment of 120 KN.m. the beam is reiforced with 4-25 mm diameter bars with modular ratio n=8. 1.) compute the Moment of Inertia of the beam. 2.) Compute the maximum stress of concrete in Mpa. 3.) Compute the Maximum Stress of Steel in Mpa. 200 500 550 4-25mm dia
hinz 1. For the beam cross section below, determine the amount of steel As required to cause the strain in the tension steel & to be 0.005 just as the maximum strain in the concrete reaches 0.003. fc' = 3000 psi and fy = 60,000 psi. N.A. b= 10"- Cross Section d = 23" [7422 4233 134 S THE THE CALE DES 2 23-c me Like phans 0.005 PANE Strain 0.003 P HOME st 0.85f Stress 6 I.C. Nc NT * * * * * Delorme
Please help. This problem involves maximum allowable stress. Thank you.
1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly rigid and sits on a 15 in x 15 in x 4 foot high concrete block which is fixed at the base. The system supports an axial load of P. A. Determine the normal stress in the steel. B. Determine the normal stress in the concrete. C. How much did the entire system shorten (Hint: the plate is perfectly rigid so it does not deform-just pretend it isn't there.) 15 in. Concrete 4 ft. 15 in. 8 in. Top View 8 in. Given: P = 250 kips L = 12 ft. d₁= 1 in. d₂ = 4 in. Esteel = 30,000 ksi Econcrete = 4,000 ksi
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
Determine the maximum and concrete and steel stresses at the point of maximum positive and negative moments. Assume a concrete cover of 40 mm, 10mm stirrups and clear distance between layers od 25mm.
1) A rectangular reinforced concrete beam with dimensions b = 14 in, d = 25 in, and h = 28 in is reinforced with three No. 10 bars. Material strengths are fy = 60000 psi and fc' = 5000 psi. a. Find the cracking moment based on the uncracked transformed section b. Determine the maximum moment that can be carried without stressing the concrete beyond 0.45fc' or the steel beyond 0.6fy. Hint: Assume maximum compressive stress in the concrete to be 0.45fc' and check whether the maximum steel stress reaches 0.6fy. This way you can check which one is reached first C. Find the nominal moment capacity of the beam
A 250 mm wide rectangular concrete beam is reinforced for tension only. The beam has an effective depth of 300 mm. fc’ = 9.3 MPa, fs = 138 MPa, n = 9. Use working stress design for balanced condition. 1. Which of the following most nearly gives the value of k. a. 0.3225 b. 0.3526 c. 0.6234 d. 0.3775 2. Which of the following most nearly gives the value of j. a. 0.7482 b. 0.8472 c. 0.8742 d. 0.4278 3. Which of the following most nearly gives the balanced moment capacity of the beam in kN.m. a. 34.52 b. 45.36 c. 36.7 d. 32.3