A rod has a solid circular cross section with a diameter eOX=IxyGiven:The area moment of inertia of a solid circular cross section about its neutral axis is hu-R¹1/4The polar moment of inertia of a solid circular cross section about its neutral axis is hu-R/2The centroid of a semi-circle is located at 4R/(3r) from the horizontal axis representing the diameter line.1500 N600 N24.5 Mpa 50.6 Mpa30.2 Mpa 14.6 Mpa -7.3 Mpa200 mm100 N-m-24.3 Mpa40 mm is subjected to the shown loads. Determine the state of stress at point.&800 N100 mmsO

To find: The state of stress at point A. Given: The area moment of inertia of solid circular cross…

A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads. Determine the state of statt.& CTX= Ixy Givenc The area moment of inertia of a solid circular cross section about its neutral axis is hu- The polar moment of inertia of a solid circular cross section about its neutral axis isu-2 The centroid of a semi-circle is located at 4R/3m) from the horizontal axis representing the diameter line 1500 N 600 N 200 mm 100 N-m 24.5 Mpa 50.6 Mpa-24.3 Mpa 30.2 Mpa 14.6 Mpa -7.3 Mpa 800 N 100 mm

A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads. Determine the state of statt.& CTX= Ixy Givenc The area moment of inertia of a solid circular cross section about its neutral axis is hu- The polar moment of inertia of a solid circular cross section about its neutral axis isu-2 The centroid of a semi-circle is located at 4R/3m) from the horizontal axis representing the diameter line 1500 N 600 N 200 mm 100 N-m 24.5 Mpa 50.6 Mpa-24.3 Mpa 30.2 Mpa 14.6 Mpa -7.3 Mpa 800 N 100 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Related questions

Q: Determine the binary diffusion coefficient of H₂ in air at 600 K and 3 atm in m²/s. (A) 17.23x10-5…

Q: Determine the force in each member of the loaded truss shown using methods of joints. B C 3 m 4 m F…

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: What is v1 and u1?

Q: A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge…

A: Given:Water flow rate, Q=0.23 m3/sSuction flange diameter, ds=304.8 mm=0.3048 mDischarge flange…

Q: A car P travels along a straight road with a constant speed v = 56 mi/hr. At the instant when the…

A: Given data:- A constant speed v = 56 mi/hr. The angle θ = 62°, d=109ft . To find:- the rate at…

Q: Oil(light) enters a heat exchanger at 450 K with a mass flow rate of 10 kg/s and exits at 350 K. A…

Q: 900 N/m A 3 m 600 N/m 3 m F

Q: A 5-kg crate is released from rest at Point A of a 20-kg ramp which is inclined at 40 degrees as…

Q: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam.…

A: We know that when two forces are present in two axes then both bending and longitudinal stress occur…

Q: Two forces and one couple act on the rigid pipe, shown in figure below. Determine their equivalent…

Q: As temperature increases, the saturation vapor pressure over a water surface increases…

A: Given information:- the saturation vapor pressure over a water surface To find:-behavior of the…

Q: Water vapor at 5 bar, 320 °C enters a turbine operating at steady state with a volumetric flow rate…

A: (a) Write the given data. P3=5 barT3=320 °CV˙3=0.65 m3/sP4=1 barT4=160 °C

Q: For a point on a steel specimen, the principal stresses are calculated as 1 = 200 MPa and 2 = -40…

Q: Draw the shear-force and bending-moment diagrams for a simple beam AB supporting two equal con-…

Q: n 8.36 A structural steel built-up section is fabricated as shown. Calculate (a) the moments of…

Q: Calculate the convective heat transfer rate via the top and the two side walls of a refrigerated box…

A: Given Data The velocity of the cruiser is:V=31.3 m/s The length of the box trailer is:L=16 m The…

Q: Refrigerant 134a is stored inside an uninsulated rigid tank (see figure below) and heated by an…

Q: Ideal gas law is stated as OP=RT/p OR=PTP P = R Tp None of the above

A: Ideal gas law is

Q: (8) An SI, six-liter, V8 race car engine operates at WOT ( wide open throttle) on a four- stroke…

Q: Given p = [1, 2, -1], q= [4, 4, -7] find (a) p.q (b) ||pq|| (c) proją(p) (d) the cosine of the angle…

A: We have, p= [1, 2, -1] and q= [4, 4, -7]

Q: Determine the quality of the steam at the turbine exit. Use steam tables. (You must provide an…

A: At turbine inlet state, P1=10MPa and T1=5000Ch1=3375.1 kJ/kgs1=6.5995 kJ/kg KAt outlet P2=25 kPafor…

Q: What is NOT an example of unsteady-state flow? a. Deflating a helium balloon b. Filling up an…

A: unsteady flowIn which flow parameters (velocity, pressure and cross- section) change with respect…

Q: Ap 60° B 4 m- - 4 m- E 4 m 60° P

Q: 2. Find stiffness matrix for he spring system. U1 k(1) ww k(3) ww U4 Lui L k(2) ww U₂ U3

Q: The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (106) m 4, and…

Q: Determine the equivalent state of stress on an element if it is oriented 40° clockwise from the…

A: Given data:- force in x direction (σx) =250MPa (positive) Force y direction(σy) =-150MPa (negative)…

Q: Refrigerant 134a is the working fluid in a refrigeration cycle shown in the figure. The R134a enters…

A: Solution: Given Data: P1=0.6 barT1=-35oCP2=10 barT3=36oCη=80%m.=0.08 kg/s To Find: (a) The…

Q: 5. A disc of diameter 0.4 meters is rotating at 30 RPM in air. The air is at 1 atm, 300K. The disc…

A: Givend=0.4mN=30 rpmTair=300KTdisc=350K

Q: An electrical-resistance strain gage records a strain of 400 μm/m on a steel tension member. What is…

Q: Two masses m₁ = 4.6kg and m2 = 10.5kg are attached to the ends of a massless string passing through…

A: Given data as per question m1=4.6 kgm2=10.5 kgg=9.81 m/s2

Q: What are the hardware implementations needed for making a 'Smart Walking Stick' for the blind? Could…

A: The hardware implementations needed for making a smart walking stick are explained as follows,

Q: A rectangular channel is 3.5 m wide and conveys a discharge of 15.0 m³/s at a depth of 2.0 m. It is…

Q: A beam 3 m long is simply supported at each end and subjected to a moment of 9 kNm at a point B, 2 m…

A: Given DataMB=9kNmAB=2mBC=1mEI=30kNm2

Q: The assembly shown in the figure is made up of a disk, a bar, and a sphere. Disk A is pinned at O…

A: Given data: md= 18 lbmR=2.7 lbms=11.5 lbRd=2ftlR=1 ftRs=0.5 ft

Q: A thermopane window consists of two glass panes, each 0.50 cm thick, with a 1.0-cm-thick sealed…

A: Given: Thickness of each glass pane bg = 0.5 cm =0.005 m Thickness of layer of air ba = 1 cm = 0.01…

Q: If the diametral pitch is 6 teeth per mm, what is the tooth thickness for a 14.5 degree composite…

Q: A -150- 50 200 rpm 45° 10 200 100 B 50 S 90 Fig. 3.35 12. Figure 3.35 shows a mechanism in which O…

Q: Locate the centroid of the plane area shown if a = 2.2in. Round the final answer to two decimal…

A: Given data:- a=2.2 in To find:- Centroid of the plane Centroid ;- it is a geometric center of the…

Q: The mass conservation law is applicable to Incompressible flow Viscous flow Compressible flow All

Q: give the angle that the hinge force at C makes with the horizontal

A: Given: Weight of the block→W=6 KN (vertically downward) Force acting at 1.5 m away from…

Q: Problem 2: Determine the reactions on member ABC at A and B.

Q: The acceleration of a particle moving horizontally under rectilinear motion is defined by the…

Q: In an air heating system, heated air at 40°C and 105 kPa (absolute, p=1.1683 kg/m³, μ-1.918 × 10-5…

A: Given: ρ=1.1683kg/m3 μ=1.918×10-5kg/m.s a×b=0.3m×0.2m V˙=0.5m3/s L=40m

Q: Calculate the moment of inertia of the shaded area about the x-axis as shown.

Q: V Wind tunnel test section km/h Model FD Moving belt Drag balance The aerodynamic drag of a new…

Q: steam power plant is equipped with a condenser that removes 500 MW of heat from steam condensing at…

A: Given:Heat removed from the condenser, Q=500 MWTemperature of condensing steam, Tc=30°COveraal heat…

Q: Problem 6 An 02-series single-row deep-groove ball bearing with an 80 mm bore is loaded with a 5-kN…

A: Given Datad=80mmFa=5kNN=500 rpmb=1.483Fr=9kNC10=70.2kNxo=0.02 Following the table of 11.1 & 11.2…

Q: An airfoil is being tested in a low-speed subsonic wind tunnel. The velocity of the flow in the test…

A: Given question is related to fluid mechanics. Given data: Velocity of flow = v = 81 ft/s…

Q: Two passenger cars are traveling at 88.5 kph. The weight of car A is 9000 N and that of car B is…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

A rod has a solid circular cross section with a diameter e
OX=
Ixy
Given:
The area moment of inertia of a solid circular cross section about its neutral axis is hu-R¹1/4
The polar moment of inertia of a solid circular cross section about its neutral axis is hu-R/2
The centroid of a semi-circle is located at 4R/(3r) from the horizontal axis representing the diameter line.
1500 N
600 N
24.5 Mpa 50.6 Mpa
30.2 Mpa 14.6 Mpa -7.3 Mpa
200 mm
100 N-m
-24.3 Mpa
40 mm is subjected to the shown loads. Determine the state of stress at point.&
800 N
100 mm
s
O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Using integration, compute the polar moment of inertia about point O for the circular sector. Check your result with Table 9.2.
Q.2) Calculate the moment of inertia (Ixc and Iyc) 0.165 m about the given axis for the composite area shown in figure. 0.8 m C 0.1m 0.265 m 1m 0.5m
The moments and product of inertia of an L4 x 3 x 1/4-in. angle cross section with respect to two rectangular axes x and y through C are, respectively, Ix = 1.33 in4. Iy = 2.75 in4, and Ixy <0, with the minimum value of the moment of inertia of the area with respect to any axis through C being Imim = 0.692 in 4 Using Mohr’s circle, determine (a) the product of inertia Ixy of the area, (b) the orientation of the principal axes, (c) the value of Imax.
Determine the second moments of area in m* and the radii of gyration in meters for the shaded area shown about the x-axis and the y-axis. y (m) -ху %3D 10 5 4 2 X (m) 6 1 2 3 4 5 105 X m4 35 X m4 %3D Kx m %D Ky %D m 3.
A channel and a plate are welded together as shown to form a section that is symmetrical with respect to the y axis. Determine the moments of inertia of the combined section with respect to its centroidal x and yaxes if a = 14 in. 0.5 in. y C a CS×115 The moment of inertia with respect to the x axis is The moment of inertia with respect to the yaxis is in4 in4 K
3:59O l 37.6 26) K/s REC Question v? = 400x Determine the moment of inertia for the shaded area shown about the x - (100 – x)- dy axis. 200 mm 100 mm 27:082021 BME 1205 Moment of Inertia Natukunda Faith's screen
a. find the area and vertical distances from the bottom edge of the cross-section to the centoid of rectangles b. Find Iz, the area moment of inertia about the z centroidal axis for the cross-section. c. Find QH, the first moment of area about the z centroidal axis for the entire area below point H. This area has width 2c2c and height tt. Also, find QK, the first moment of area about the z centroidal axis for the entire area above point K with width b and height t. d. Determine the magnitudes of the shear stress at point H and the shear stress at point K. e. Find Qmax, the maximum first moment of area about the z centroidal axis for any point in the cross section, and τmax, the maximum horizontal shear stress magnitude in the cross section.
Polar moment of inertia (I,), in cm, of a rectangular section having width, b 2 cm and depth d = 6 cm is %3D
A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area (I) of a beam with a rectangular cross-section is 11.50 x 106 mm4 about its centroidal x-axis and the depth dimension (d) of the rectangular section is 180 mm, determine the breadth dimension (b) for this beam section. Give your answer in millimetres (mm) and to 2 decimal places. Assume the beam section material is homogeneous.
The shaded area has the following properties: Ix=1.26x10^6 mm^4, Iy=6.55x10^5 mm^4, Pxy=-1.02x10^5 mm^4 Determine the maximum moment of inertia and the minimum moment of inertia
29 - Find the center of gravity M (x,y,z) of the three-dimensional homogeneous ABCD wire in the figure by using the coordinate set. The dimensions of the wire are a= 24 cm, b= 36 cm. In which of the following options are the coordinates of the AB part of the homogeneous wire in the x, y and z axes given correctly?A) (36 ; 24 ; 12)B) (18 ; 12 ; 0)C) (36 ; 12 ; 0)D) (36 ; 24 ; 0)E) (36 ; 12 ; 24)
13 - Find the center of gravity M of the three-dimensional homogeneous wire ABCD using the coordinate set (x, y, z) in the figure. The dimensions of the wire are a = 24 cm, b = 36 cm. The coordinates of the AB part of the homogeneous wire in the x, y and z axes are given in the following:A) (36; 12; 0)B) (36; 24; 0)C) (36; 24; 12)D) (18; 12; 0)E) (36; 12; 24)