A Rectangular Hollow Section (RHS) member with span length of 4 m is subjected to an axial compressive force of 200 kN and a constant 20 kNm bending moment about y-axis. Assess the suitability of a hot-rolled RHS (120 x 80 x 10) in grade S275 steel by using alternative method 1 (Annex A).

A Rectangular Hollow Section (RHS) member with span length of 4 m is subjected to an axial compressive force of 200 kN and a constant 20 kNm bending moment about y-axis. Assess the suitability of a hot-rolled RHS (120 x 80 x 10) in grade S275 steel by using alternative method 1 (Annex A).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem #3: Determine the force in members AF, BF, and BC, and state if the members are in tension…

Q: The prestressed concrete girder is made from plain stone concrete and four 3/4-in. cold-form steel…

Q: Fluid flows at the rate of 0.272 m/s in a 925 mm diameter pipeline 588 m. long. Specific gravity of…

A: V = 0.272 m/s D = 925 mm or 0.925 mL = 588 m f = 0.012

Q: A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward…

A: Width of flange, Thickness of flange, Depthe of section, Web thickness, To find: (a) Type…

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

Q: 4.4 Determine the increase of pore water pressure at M due to the strip loading shown in Figure P4.2…

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: For the equilibrium to satisfy the centroid of the section should pass through O

Q: A reservoir had an average surface area of 20 km² during September 2008. In that month, the mean…

Q: The two beams are connected by an ideal pin at C. Draw the shear and moment diagrams for the…

A: Given:Required:Shear force and bending moment diagramMaximum magnitude of bending moment in each…

Q: The PureNSafe Company is designing a solar-driven, portable water disinfection system to be used by…

A: Disinfection rate constant for UV light (k)= 7.50 s-1The required reduction in bacterial countc= 3.5…

Q: ~Using

Q: Determine the displacement ad rotation at start and end point of the beam 6 kN/m 2m 2m 6 kN/m 2 m

Q: 1949 mm Water 343 mm 2167 mm Mercury Fig. 1: A U-tube manometer to measure the pressure difference…

Q: If a dairy processing factory produces an average of 246 m³/d of wastewater with a BOD5 of 1400…

A: A dairy processing factory produces discharge Q= 246 m3/d of wastewaterper capita daily sewage flow…

Q: Q3- A soil sample has a void ratio of 0.72, moisture content = 12% and Gs=2.72 determine the…

Q: The half-life of 222 Rn is 4.2 days. A sample of 222 Rn is allowed to decay for 17.2 days and after…

A: As per question , This question is related to Environment Engineering.Given data - Half life = 4.2…

Q: A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure…

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

Q: a) Determine the force in member BG of the truss. b) Determine the force in member CD of the…

Q: If the velocity head at one point of a pipeline is 5 m, determine the velocity head at another point…

A: Velocity head = 5m Velocity increasing 3 times = velocity at that point = 3v

Q: Problem: A 2 story bank is constructed with reinforced masonry walls and the floor and structural…

A: A "2-story bank" is a building that houses a bank and has two stories or levels and the bank has two…

Q: 8-3 Why do bar spacing and cover to the surface of the bar affect bond strength?

A: Given data,question given related to the reinforced cement concreteLet's discuss the reason of…

Q: SAMPLE PROBLEM 2: VSE LRFD W21 x 62 steel is used as a beam simply supported over a span of 8m. The…

Q: 1. Draw the shear and homent diagrams for the beam shown in Figure 1. EI is constant. Neglect the…

Q: is to be connected using 3/4-in diameter bolts. Use NSCP Specifications. - Standard-sized holes - Fy…

A: L = 21 ftPDL = 100 kipsPLL = 120 kipsdb = 3/4 indbo = 3/4+1/8 = 0.875 inFy = 36 ksiFu = 58 ksi

Q: A beam is subjected to the loading condition shown below. Determine the displacement at A and the…

A: “Since you have asked for multiple methods, we will provide the solution only using the first method…

Q: B. Find forces in members CF, CG and GE of truss (b) using appropriate sections 30 k 30 k 41 30 k- F…

Q: A bearing plate is to be designed for a W21x62, A36 steel beam that will sit on a reinforced…

A: The steel section used as bearing plate = W2162The yield strength of steel (fy) = 345 MPaThe…

Q: Use the singly constraint growth factor model to calculate the projected trips in Cell (1,2) for the…

Q: 1 A steel bar is 40 mm in diameter for a length of 100 mm, 30 mm in diameter for a length of 60 mm…

A: Reinforcing bars, or rebars, are a type of steel bar. It's a steel wire mesh that's used as a…

Q: A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown…

Q: Principles of Steel Design Plate no. 8: Elastic and Plastic Properties Compute the elastic moment…

A: 1) 2)3)A36 : Fy=248 Mpa

Q: Following results were recorded from a consolidation test on a specimen of saturated clay, each load…

A: After subjecting a saturated clay specimen to a consolidation test, each load was held constant for…

Q: = 7-57. The beam is subjected to a shear force of V Determine the maximum shear flow in the cross…

Q: gure 1 shows a cross-section through an excavation in a deep sand deposit. The site engineer…

Q: Two large water reservoirs with a water level difference of 12 m are joined together with two pipes…

A: Elevation difference , Z = 12 m D1 = 200 mm or 0.2 m D2 = 100 mm or 0.1 m

Q: Flexible Pavement Design Assume the thickness of Base Course and Sub Base Course. Compute the SN of…

Q: The dresser has a weight of 80 lb and is pushed along the floor as shown in (Eigure 1). Assume h =…

A: Part A) Calculate the minimum force to move,

Q: Analyze the truss for reactions and axial forces and input the answers (2 decimal digits) to the…

A: A truss is given we need to find out the reactions and member force

Q: It is required to design a combined footing for two RCC columns spaced at 4.5 m C/C. The columns are…

Q: How do you get the valuse for V mid and V mean?

Q: (2) Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the…

A: The continuous beam with an internal hinge is shown in the above figure. We have to find out the…

Q: 13 kip/ft -6 ft C 4.5 ft-4.5 ft- B

Q: Determine the factor of safety of the slope shown in the figure below using an ESA and a TSA. The…

Q: Problem 4: Kinetic Head no picture necessary Use the Rayleigh Method to show that velocity head is…

Q: H.W: Find forces and elongations wires, steel in each wire. A=80mm² L=4m E=200 G Pa Estrelaxation.…

Q: Propose an example similar to the problem posed, where the soil is cohesive-frictional.

A: We have to discuss an example similar to the problem posed in the earlier question, where the soil…

Q: For the roof truss shown, determine the axial forces in members AD, BD, DE, and DG and state whether…

A: Let us draw the given diagram and find the supporting forces.

Q: 3.24 The four forces are in equilibrium. Deter- mine F, and 0, (a) graphically from the force…

Q: N/m^3. B 5 D.D.

Question

100%

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

Calculate the shear yield stress (ksi) of A588 steel.
Topic: COMBINED STRESS-AXIAL TENSION AND FLEXURE BENDING: STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee Questions A Tension member with no holes is subjected to axial loads of PD=68kN & PL=64kN.It is also subjected with bending moments of MDy=40kN-m & MLy=55kN-m. Is themember adequate? Steel is of A992 Gr 50 Specs. Use LRFD. Neglect the weight of the beam. Section properties:Lp = 1.863 md=459.99mmtw=9.02mmzx= 1835x10^3 mm^4Lr = 5.305 mLb = 4.8 mbf=191.26mmtf=16mmSx=1611x10^3 mm^4 Sy=195x10^3 mm^4Zy=303x 10^3 mm^4 Cb=1.32
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area c. Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 90m²m 90 mm 90mm 45 45mm In my comin P Scanned with CamScanner CS
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
Regular low-alloy steel has an allowable shearing stress of approximately 20.0 ksi (Fv = 20.0 ksi). The beam shown has an unusual loading pattern that will cause very high shearing forces. If this beam is a W30 X 173, will it be adequate in shear?
Specify a suitable aluminum casting alloy for a bar with square crosssection. Length of one side of the cross-section is 50 mm. The bar is subjected toan impact loading with a tensile force of 60 kN
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 25 mm= DIAMETER OF BOLTS 45 45mm fmmy C. 90mm 90mm 90mm Comm P
limit of this steel is 34,000 psi. 10.2 A concrete cylinder 150 mm in diameter was t tested in com- pression and found to be shortened an amount of 0.074 mm over a length of 300 mm. The load at the time of the reading was 89 kN. Compute the modulus of elasticity. 10.3 A mild steel, known to have a proportional limit of 34,000 psi,
Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
Problem2. The compression member is shown in figure. Find the following: a. The Euler stress Fe. b. The buckling stress Fcr c. The design strength d. The allowable strength e. Does the member satisfactorily meet the design requirements? Why? HSS 8x 8x4 ASTM AS00, Grade B steel (Fy = 46 ksi) 15'
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)