A platinum resistance temperature detector (RTD) is used to measured temperature of the hot gas. The resistance of sensing element is 250.3 ohm when it contact with hot gas. calculate the temperature of the gas. The RTD has a resistance of 120 ohm and 80 ohm at 100°C respectively. The temperature coefficient of platinum is 0.0039 C^-1.

A platinum resistance temperature detector (RTD) is used to measured temperature of the hot gas. The resistance of sensing element is 250.3 ohm when it contact with hot gas. calculate the temperature of the gas. The RTD has a resistance of 120 ohm and 80 ohm at 100°C respectively. The temperature coefficient of platinum is 0.0039 C^-1.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter3: Static Electricity

Section: Chapter Questions

Problem 7RQ: A thundercloud has a negative charge, and an object on the ground has a positive charge. Will the...

See similar textbooks

Similar questions

A platinum resistance temperature detector (RTD) is used to measured temperature of the hot gas. The resistance of sensing element is 250.3 ohm when it contact with hot gas, calculate the temperature of the gas. The RTD has a resistance of 120 ohm and 80 ohm at 100°C respectively. The temperature coefficient of platinum is 0.0039 C^-1.
Which material is always conductive? Metal semiconductor Insulator
Copper is a Select one: O a. Semiconductor O b. Conductor Super Conductor O d. Insulator
10) A certain batch of copper wire was found to have a conductivity of 98% at 20°C. What is its resistivity in uQ-cm?
Electrical circuits Please help me fast
State the different damages of diodes
Electromagnetcs
Question 13 Not yet answered Marked out of 1.00 P Flag question Which of the following ratings (PIV- Peak Inverse Voltage and temperature) is true? Si diodes have lower PIV and narrower temperature ranges than Ge diodes. Si diodes have lower PIV and wider temperature ranges than Ge diodes. Si diodes have higher PIV and wider temperature ranges than Ge diodes. Si diodes have higher PIV and narrower temperature ranges than Ge diodes.
Determine 1) the maximum load current. 2) the mean load current .3)the rms alternating load current. 4) the DC power supplied to the load. 5) the input power to the anode circuit. 6) the rectification efficiency. 7) the percentage of regulation. 8) the ripple current. R=10°0 Vi R=10°n AC Figure (2-72) the circuit of problem (2-6). (2-7) A full-wave bridge rectifier with a 120 Vrms sinusoidal input has a load resistance of Ikn. Determine:- 1) The de voltage available at the load. 2) Find the maximum current through each diode during conduction. 3) What is the required power rating of each diode. (2-8) A zener diode has a de power dissipation of Iw and a zener voltage rating of 27v. What is the value of I, max for the device? (2-9) Calculate and draw the output voltage for the circuit shown in Figure (2-74). +100v Vo 2.2kd4 2.2kQ -100v Figure (2-74) the circuit of problem (2-10).
The primary voltage on the transformer in Figure 2–46 (p. 96) is 120 V rms and NP : NS = 15:1. Diode voltage drops are 0.7 V. (a) What should be the value of RL if the average current in RL must be 0.5 A? (d) Is it alright to measure with an oscilloscope both the input and output waveforms at the same time in Figure 2-46? Why or why not?
What should I do when I get a current like 0.263187845A, should I round into the simplest form, or keep it and convert into mA?
Determine whether the diode in the circuit will be conducting or not