A pipe 200 m long as shown in the figure tapers from 0.80 m diameter at the higher I end to 0.40 m diameter at the lower end carries 100 liters per second of oil (sp.gr.=0.85). If the pressure gauge at the lower end reads 50 KPa, determine the velocities at the two ends and the pressure at the higher end. Neglect all losses.

A pipe 200 m long as shown in the figure tapers from 0.80 m diameter at the higher I end to 0.40 m diameter at the lower end carries 100 liters per second of oil (sp.gr.=0.85). If the pressure gauge at the lower end reads 50 KPa, determine the velocities at the two ends and the pressure at the higher end. Neglect all losses.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is stored in a tank sketched in the figure below to support the demand of a nearby community area.The system is designed so that pressure at the location B always lies in the range of 330 to 440 kPa (gauge).Water demand fluctuates between 0.3 and 1 m3/s regardless of pressure at B. The supply pipe of 600 mmdiameter and 1 km length between A and B is made of steel and has the equivalent sand roughness of 1 mm.Although not shown in the figure, the supply pipe has five 90◦ bends, each having the head loss coefficientof 0.8. The figure shows that the bottom end of the tank is located 42 m above the ground, and the pipe isburied 1.5 m below the ground. A pump system regulates so that the tank keeps the same water level all thetime. Assume water at 20◦C, and air in the storage tank has the atmospheric pressure. To meet the designcriterion for pressure at B, what should be the depth of water h in the storage tank?
As shown in the Video and in the figure below, water "bubbles up" 9 in. above the exit of the vertical pipe attached to three horizontal pipe segments. The total length of the 0.75-in.- diameter galvanized iron pipe between point (1) and the exit is 27 inches. Determine the pressure needed at point (1) to produce this flow. (1) (2) 9 in. 10in. (3) P1 = the tolerance is +/-2%
Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius horizontal pipe. If the bore of the pipe is reduced to 2.7-in radius and the pressure in the smaller pipe is 93 psig, what is the pressure in the larger section of the pipe? Include schematic diagram.
The standpipe is connected at C to the field storage tank with oil, and the system is open to the atmosphere at B and E. Suppose that hj = 9 ft , hɔ = 5.5 ft and h3 = 8 ft. Take po = 1.78 slug/ft³. (Figure 1) Figure 1 of 1 B 4 ft E hi F h3 C h2 If the level of oil in the pipe is at F, determine the largest gage pressure in the tank in psi. Express your answer to three significant figures and include the appropriate units. At what level should the oil be in the tank, so that the maximum gage pressure occurs in the tank and the oil doesn't flow out from the tank at B? O F O A ОЕ Ос Ов What is the value of the maximum gage pressure that can occur in the tank if oil doesn't flow out from the tank at B? Express your answer to three significant figures and include the appropriate units.
For the Pipe shown Q=4250 gallons per minute (gpm), P1=132 kPa and P2 = 211 kPa. If the pipe carries a special fluid of SG=1.2, determine the pressure head at section 2. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3
Q1) Water flows in a pipe branch installed vertically, as shown in Figure 1. The pipe branch is supported from moving by using an anchor block. The anchor block is able to hold the pipe in y-direction. Determine the minimum branch angle, 0, that is able to withstand the movement in x-direction, given the horizontal force component of the anchor block is Rx= 5.5 kN. Ignore major and minor losses in your calculation. 0₂: = 0.25 m 2 P₂ = ? kPA 0₁ = 0.4 m P₁ = 360 kPA Q₂ = 0.24 m³/s Q₁ = 0.73 m³/s V₁ +у + X 1 03 03 = 0.65 m P3 = ? kPA Q3 = ? m³/s 0/2 0/2 V₂ Rx 3 0.7 m 0.7 m
A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. a. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? b. After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? c. What will be the absolute pressure (P3) in the smaller pipe? d. What is the volume flow rate through the smaller pipe?
Q1: In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical U tube containing mercury. If the difference level between the fluids in the U-tube arms is (x +) in cm, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe. Throat Area, A On, S-0.85 k+(1/S.Nin cm Manometer - Mercury S-136
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
Q6/ Determine the pressure difference between pipes A and B for the differential manometer shown in Fig. Q7/A shaft of diameter 120 mm is rotating inside a journal bearing of diameter 122 mm at a speed of 360 rpm. The space between the shaft and bearing is filled with lubricating oil of viscosity 6 poise. Find the power absorbed in the oil if the length of bearing is 100 mm. Water Water Water ito 1.2 m 1.5m 0.5m Im Mercury (sp gr = 13.6) 1.3 m
2) The horizontal pipe of diameter 240 mm is suddenly enlargement to a diameter of 480 mm. if the pipe carries water at 325 liters/sec, calculate the (i) Head loss to sudden enlargement,(ii) Pressure loss across the enlargement (p1-p2).
Oil (SG = 0.84) is flowing in a pipe under the conditions shown in Figure. Find the pressure at point 2