A parabolic reflector focuses electromagnetic waves into a beam as shown in the figure. The electromagnetic radiation is pulsed,with a pulse frequency of 16.0 GHz, and the duration of each pulse is t = 1.00 ns. The face of the reflector has a radius of5.00 cm, and the average power during each pulse is 20.0 kW. (Due to the nature of this problem, do not use roundedintermediate values in your calculations-including answers submitted in WebAssign.)(a) What is the wavelength (in cm) of these electromagnetic waves?cm(b) What is the total energy (in µJ) contained in each pulse?(c) Compute the average energy density (in mJ/m³) inside each pulse.mJ/m³(d) Determine the amplitude of the electric field (in kV/m) and magnetic field (in µT) in these electromagnetic waves.EmaxkV/m%3DB maxHT(e) Assuming that this pulsed beam strikes an absorbing surface, compute the force (in uN) exerted on the surface during the1.00 ns duration of each pulse.µN

In the question, the following data is given. frequency (f) = 16 GHz Time Duration (t) = 1.00 ns…

A parabolic reflector focuses electromagnetic waves into a beam as shown in the figure. The electromagnetic radiation is pulsed, with a pulse frequency of 16.0 GHz, and the duration of each pulse is t = 1.00 ns. The face of the reflector has a radius of 5.00 cm, and the average power during each pulse is 20.0 kW. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.)

A parabolic reflector focuses electromagnetic waves into a beam as shown in the figure. The electromagnetic radiation is pulsed, with a pulse frequency of 16.0 GHz, and the duration of each pulse is t = 1.00 ns. The face of the reflector has a radius of 5.00 cm, and the average power during each pulse is 20.0 kW. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1(a) Analyze the polar form of this waveform in Figure Q1(a). 60 V 310⁰ Figure Q1(a)
draw a handdrawn clear picture of 34 conductors,17 slots ,4 poles wave winding .a computarized picture is given(the upper one)
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 5.3 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 5.9 cm respectively. The difference between the two waveforms is 0.7. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency
The value of armature current in the waveform is 12 A, a = 52 degrees, and ß = 154 degrees. The RMS value of current is Ia a+T B+TT a 4.62 68.38 O 9.03 O 2.61
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.5 cm and 5.5 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform
Explain this. it is a -4 poles -26 conductors -double layer -simplex wave winding
What is the ripple factor of a DC signal having ripple voltage of 2 V and a DC voltage of 50 V? Answer in percentage % O 8% O 1.2% O 2.83% O 4.0%
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 7.1 cm for both the waveform. The Peak to Peak height of waveform G and H are 5.6 cm and 5.7 cm respectively. The difference between the two waveforms is 1. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform a) frequency b) phase difference c) RMS value of G waveform d) Peak value of H waveform
Referring to Figure 5 above, given power R1 = 40 W, power R2-20 W, power R3 = 20 W, power R4-40 W, power R5-20 W, power R6-40 W, power R7-40 W and Voltage AC-220 V pmkd, Frequency 50 Hz. Calculate. The time taken for one sine wave cycle for the frequency of that circuit
A double beam oscilloscope displays 2 sine waveforms A and B. The time/cm switch is on 150µs/cm and the volt/cm switch on 5 V/cm. The width of each complete cycle is 8 cm for both the waveforms. The height of waveforms A and B are 5 cm and 4 cm respectively. Determine their a) frequency, b) phase difference, and c) peak and d) r.m.s value of voltages. The difference between the two waveforms is 0.7 cm.
A pure sinusoidal current is being rectified. For the given maximum value of half wave rectified current is 50 A, then the rms value of full wave rectification will be 50 (a) 100 (b) - - (c) 100 A (d) 70.7 A
5. Let's change our square wave to be less square. We're only going to have it be at the high voltage for 25% of the cycle. Sketch what you would expect Vout to look like now: ha n 2.T V S T 3T t