A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. Thecoefficient of friction between the ladder and the horizontal surface is =0.215 and the coefficient offriction between the ladder and the wall is = 0.253. Determine the maximum angle with the vertical theladder can make without falling on the ground.8.

Answered: Image /qna-images/answer/89ebb96f-c799-4db5-81df-e9f549c98057.jpg

A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. The coefficient of friction between the ladder and the horizontal surface is p= 0.215 and the coefficient of friction between the ladder and the wall is = 0.253. Determine the maximum angle with the vertical the ladder can make without falling on the ground.

A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. The coefficient of friction between the ladder and the horizontal surface is p= 0.215 and the coefficient of friction between the ladder and the wall is = 0.253. Determine the maximum angle with the vertical the ladder can make without falling on the ground.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.55P: A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of...

See similar textbooks

Similar questions

A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
Determine the smallest horizontal force P that must be applied to block B to cause impending motion. The angles of static friction are 15 between the blocks and 30 between the blocks and the ground.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Three identical blocks are placed on top of each other on a horizontal plane. Each block has a weight of 110 lb and the coefficient of friction between all surfaces is 0.25. If the upper most block is prevented from moving by a horizontal cable to a vertical wall, find the horizontal force that must be applied at the middle block without causing motion to impend. Pls show full solution with figures.
A. Determine the angle between the wedge and the concrete and the wedge and the floor. B. Calculate the coefficient of static friction between the concrete and floor.
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o
A 200 lb block is in contact with a plane inclined at 30 degrees to the horizontal. A force P, parallel to and acting up the plane, is applied to the body. If the coefficient of static friction is 0.20, find: a. the value of P to just cause the motion to impend up the plane b. the value of P just to prevent motion down the plane c. the magnitude and direction of the friction force F if P= 80 lbs
A uniform ladder of length L and weight w is leaning against a vertical wall. The coefficient of static friction between the ladder and the floor is the same as that between the ladder and the wall. If the coefficient of static friction is 0.360, determine the smallest angle the ladder can make with the floor without slipping.
4. Determine the smallest horizontal for P required to pull out a wedge A. The crate has weight of 300 Ib and the coefficient of static friction at all contacting surfaces is 0.3. Neglect the weight of the wedge. 1S 5. For a systerm shown, determine the maximum weight of the box that will cause the crates to move up. Use coefficient of friction for contact surface, 0.35. 7
A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. The coefficient of friction between the ladder and the horizontal surface is ?1=0.245 and the coefficient of friction between the ladder and the wall is ?1=0.253 . Determine the maximum angle α with the vertical that the ladder can make without falling on the ground.
The coefficient of friction for both surfaces is 0.20. The force P that will cause impending motion is nearest: