A laboratory study models the flow around the pier of an off-shore wind turbine with a scaled model of Lr = 20. Determine the model velocity (VM) past the pier, if the water travels with V = 2.2 km/h past the prototype pier. You can assume that water with the same fluid properties is used in both model and prototype with density of Pw = 1005 kg/m³ and dynamic viscosity of nw = 0.001 Pa . s. HINT: the flow around the pier is described by the Reynolds number.

A laboratory study models the flow around the pier of an off-shore wind turbine with a scaled model of Lr = 20. Determine the model velocity (VM) past the pier, if the water travels with V = 2.2 km/h past the prototype pier. You can assume that water with the same fluid properties is used in both model and prototype with density of Pw = 1005 kg/m³ and dynamic viscosity of nw = 0.001 Pa . s. HINT: the flow around the pier is described by the Reynolds number.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
An airplane wing, with chord length of 1.5 m and span of 9 m, is designed to move through standard air (v= 1.51x105 m²/s) at a speed of 7.5 m/s. A 1/10-scale model of this wing is to be tested in a water tunnel (v= 1.00×106 m²/s). If viscous effects govern, what speed is necessary in the water tunnel to achieve dynamic similarity? a.11.33 m/s b.4.97 m/s c.1.51 m/s d.2.98 m/s
(b) A Formula 1 team tests their car in a wind tunnel at a scale of 50%, at a speed of Vwinarunnet = 50 m/s. The measured downforce at this speed is Foownforce.WT = 3000 N and the model reference area is Aref wT = 0.5 m?. 1. Find the downforce magnitude on the full-scale race car at the same Reynolds number. Assume constant air density p = 1.2 kg/m. II. It is said that F1 cars could travel upside down, as shown below. At what speed should the full-scale car travel to achieve this, if its mass is m = 740 kg? The acceleration of gravity is g = 9.81 m/s?. Downforce Weight
For studying of a dam in the laboratory, a model overflow has been built in the scale of , to 36 Prototype. The flowrate of the flow in the model is 0.15 . The required time for moving of water between two points in the model is 1 minute. Calculate: i. The volume flowrate in the prototype. ii. The required time for moving of water between the points in the prototype.
The slope of the height h of a surface wave moving in a shallow pool of liquid is related to the speed of the wave u and gravity g by the following equation и ди дх g əx (a) Use a length scale L and a velocity scale Vo to 'nondimensionalize' the equation (b) What is the nondimensional parameter of the flow?
(b) The kinematic viscosity of a fluid used for model is one third of the kinematic viscosity of the fluid used for prototype. During testing of the model, if viscosity and gravity forces are predominant, find the scale ration, velocity ratio and discharge ration
The Reynolds transport theorem (RTT) is discussed in Chap. 4 of your textbook. For the general case of a moving and/or deforming control volume, we write the RTT as follows: d pb dV + pbV-ñ dA dt dt dB sys where Vr is the relative velocity, i.e., the velocity of the fluid relative to the control surface. Write the primary dimensions of each additive term in the equation and verify that the equation is dimensionally homogeneous. Show all your work. (Hint: Since B can be any property of the flow-scalar, vector, or even tensor—it can have a variety of dimensions. So, just let the dimensions of B be those of B itself, {B}. Also, b is defined as B per unit mass.)
A liquid of density ? and viscosity ? flows by gravity through a hole of diameter d in the bottom of a tank of diameter DFig. . At the start of the experiment, the liquid surface is at height h above the bottom of the tank, as sketched. The liquid exits the tank as a jet with average velocity V straight down as also sketched. Using dimensional analysis, generate a dimensionless relationship for V as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. (Hint: There are three length scales in this problem. For consistency, choose h as your length scale.) except for a different dependent parameter, namely, the time required to empty the tank tempty. Generate a dimensionless relationship for tempty as a function of the following independent parameters: hole diameter d, tank diameter D, density ? , viscosity ? , initial liquid surface height h, and gravitational acceleration g.
The less following data is measured for the dimensionless velocity u of a fluid as a function of dimensionless location and dimension- time t: t=0 t=2 t = 4 t = 6 t = 8 x=0 0 3 14 7 5 x=0.5 8 10 14 12 10 x = 1 2 7 8 9 7 x = 1.5 13 15 22 16 9 x=2 15 18 22 17 14 By hand, calculate the acceleration of the fluid, ou/et and the spatial change in acceleration of the fluid, ²u/(Ətəx) a) at z = 1 and t4 with second order accuracy; b) at z = 0 and t = 2 with second order accuracy;
When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow andthen undergoes transition to turbulence at a time ttr which depends upon the pipe diameter D,fluid acceleration a, density ρ, and viscosity µ. Arrange this into a dimensionless relationbetween ttr and D.
using pure water at 20°C. The velocity of the prototype in seawater (p = A 1/18 scale model of the submarine is to be tested in the water tunnel 1015 kg/m³, v = 1.4x106 m²/s) is 3 m/s. Determine: a) the speed of the water in the water tunnel for dynamic similarity D) the ratio of the drag force on the model to the drag force on the prototype
A prototype ocean platform piling is expected to encountercurrents of 150 cm/s and waves of 12-s period and 3-mheight. If a one-fifteenth-scale model is tested in a wavethe channel, what current speed, wave period, and wave heightshould be encountered by the model?