a) L Question 7: A massless beam ABC of span L and con- stant flexural rigidity EI is simply supported at A and C, and it supports a mass concentrated at the midspan point B, as shown in Figure a). The natural frequency of this В El A system is expected to be 25 rad/s. However, the measured b) natural circular frequency is found to be only 23 rad/s, the lower value being ascribed to flexible supports at A and C, k Figure b). Calculate the stiffness k of the beam support k bearings as a fraction of the beam stiffness.

a) L Question 7: A massless beam ABC of span L and con- stant flexural rigidity EI is simply supported at A and C, and it supports a mass concentrated at the midspan point B, as shown in Figure a). The natural frequency of this В El A system is expected to be 25 rad/s. However, the measured b) natural circular frequency is found to be only 23 rad/s, the lower value being ascribed to flexible supports at A and C, k Figure b). Calculate the stiffness k of the beam support k bearings as a fraction of the beam stiffness.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A T-profile beam can be oriented in the four orientations shown. For the given loading, indicate which orientation(s) of the beam will result in the least displacement of the free end of the beam. ↑F TIITTIT possible orientations of beam cross section T (1) (2) (3) T (4)
From the given Figure and data below. Determine the a. P so that the structure is stable (in equilibrivum) b.Draw the FOD OF the member BC C. Rea ction at A Weight of the member AB and BC :50 kg M at C =0.5 %3D 3 m A 1.5 m 30° Mx- D.5
A catilever beam PQ of uniform flexural rigidity (El) is subjected to a concentrated moment M at R as shown in the figure L/2 P. R The deflection at the free end Q is Twwwww
EXAMPLE 4.4 Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the magnitude of P is 4 kN, determine (a) the value of Q so that the deflection at A is zero, (b) the cor- responding deflection of B. 20-mm diameter 0.4 m 0.5 m 60-mm diameter
A simply supported beam of span L is subjected to a temperature gradient which increases linearly from zero at the left-hand support to fo at the right-hand support. If the temperature gradient also varies linearly through the depth, h, of the beam and is zero on its undersurface, calculate the deflection of the beam at its mid-span point. The coefficient of linear expansion of the material of the beam is a. Ans. -ato1?148h.
Figure Q3 (a) shown a single channel structure. Determine the; (i) cross-sectional area, A (ii) centroid in y-direction, ỹ (iii) centroid in z-direction, ž (iv) second moment of inertia in y-direction, Iyy (v) second moment of inertia in z-direction, Izz
Figure P24.25a shows a uniform beam subject to a linearly increasing distributed load. The equation for the re- sulting elastic curve is (see Fig. P24.25b) EI dx Note that the analytical solution for the resulting elastic curve is (see Fig. P24.25b) Wo(-x +24x -L*x) 120 EIL Use bvp4c to solve for the differential equation for the elastic curve for L 600 cm, E 50.000 kN/cm2, I 30,000 cm, and w 2.5 kN/cm. Then, plot both the numerical (points) and the analytical (lines) solutions on the same graph.
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
Develop the flexibility matrix for the beams with respect to the co-ordinates shown in figure. 21 2m 1 I 2
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
A prismatic fixed-fixed beam, modelled with a total lumped-mass of 10 kg as a single degree of freedom (SDOF) system is shown in the figure. A B m E,I E,I 2 2 SDOF If the flexural stiffness of the beam is 4n2 kN/m, its natural frequency of vibration (in Hz, in integer) in the flexural mode will be,
Select all applicable answers. XY is projected as PV in ARP1. Which of the following projections is possible for the reference plane adjacent to ARP1? Da TL parallel to ARP1 Oa TL perpendicular to ARP1 Oa TL not parallel nor perpendicular to ARP1 Da non-TL parallel to ARP1 Da non-TL perpendicular to ARP1 Da non-TL not parallel nor perpendicular to ARP1 Oa PV