A hydroelectric power plant is being designed. The gross head from the reservoir to the tailrace is 1065 ft, and the volume flow rate of water through each turbine is 203,000 gpm at 70°F. There are 12 identical parallel turbines, each with an efficiency of 95.2 percent, and all other mechanical energy losses (through the penstock, etc.) are estimated to reduce the output by 3.5 percent. The generator itself has an efficiency of 94.5 percent. Estimate the electric power production from the plant in MW

Q: Consider two hydraulic turbines having identical specific speed and effective head at the inlet. If…

A: Given data: - The speed ratio of the two turbines is N1/N2 = 2. The expression for the specific…

Q: A turbine is rated 620 hp when the flow of water through it is 22 ft3/s. Assuming an efficiency of…

A:

Q: hydro-electric power plant has a 25MW output with an efficiency of 97%. The turbine efficiency is…

A:

Q: Why are Francis and Kaplan turbines generally consideredunsuitable for hydropower sites where the…

A: Francis and Kaplan turbines could work on a wide range of heads and flow rates. But there are so…

Q: A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. What horsepower would be…

A:

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

A:

Q: Using water jet forces to operate turbines in hydropower plant consider application of:

A: The turbine utilize he Kinetic Energy of falling water to generate rotation and subsequently…

Q: Show how the work done per second or the power developed by a tangential flow turbine runner can be…

A: Turbines are the hydraulic machines, which convert hydraulic energy into mechanical energy.…

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A: Q=0.01m3/shL=13.0 mρ=1000kg/m3μ=0.001kg/m.s

Q: Pelton turbine is the only type that is mostly used these days. It is also called free jet turbine…

A:

Q: Calculate the water power available in the pipe flowing at the rate of 0.166 m3/s with total Head as…

A: Given, Discharge , Q=0.166m3/sTotal head, h=29.9mDensity of water, ρ=1000kg/m3acceleration due to…

Q: Which of the following head is neglected in ideal Bernoulli's Energy equation   1. Head loss due…

A: Bernoulli's equation is nothing but another version of conservation of energy

Q: 1.)  A Pelton wheel with a needle-controlled nozzle develops 1 050 kW against a gross  head of 300…

A:

Q: Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The…

A: Water temperature, T=65oCWater vapour pressure at 65oC, Pv=2.503 kPaWater density at 65oC, ρ=980.5…

Q: 10. A hydroelectric power station is required to generate a total of 4.2 MW from a number of…

A:

Q: In a hydroelectric project, the upstream reservoir water level is 200 m above the tailrace water…

A:

Q: Water enters the radial turbine at 30⁰ absolute flow angle with the flow rate of 3.5 m3/s and leaves…

A:

Q: A proposed hydro-electric power plant has the following data: Elevation of normal headwater surface…

A: Given that, Elevation of normal headwater surface, H1=194 m,Elevation of normal tailwater surface,…

Q: Q.12 A Francis turbine develops 3 MW under a head of 50 m at an overall efficiency of 88%. The…

A: Given: Shaft power developed by the francis turbine=3×106WHead=50mOverall efficiency ηo=0.88Inlet…

Q: Toluene at 35 degrees Celsius is pumped from an open reservoir to a tank kept at a gauge pressure of…

A: Temperature of Toluene, T=35oCDischarge tank pressure, P1=150 kPa=150*103 PaPosition of pump below…

Q: 3. Pelton wheel runner produces 20 MW under a head of 450 m when running at a speed of 600 rpm. If…

A:

Q: The penstock if hydro-electric plant is 0.5 x 0.5 m with velocity of 5.5 m/sec has a head of 20 m.…

A: .

Q: In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F.…

A:

Q: Although hydraulic turbines considered one of the most efficient power plants, their ecological…

A: turbines are used to harness the electricity from the energy of water. Effect of Hydraulic Turbine…

Q: Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm,…

A:

Q: The diameter of a Pelton wheel is 0.7 m. The pressure head in front of the nozzle is 200 m and the…

A:

Q: 1) Interpret solar power in the context of environmental impact. 2. What is the rigid dichotomy…

A: 1) Solar power is the renewable source of energy and it is used widely around the world for power…

Q: A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the…

A: Given data A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume…

Q: what is the overall efficiency of the turbine if the power developed is 12 MW at the head of 150 m…

A:

Q: What is the overall efficiency of the turbine if the power developed is 15,000 kW at a head of 150…

A:

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

A:

Q: the available power from the physical environment. 2 the flow rate 3 the inlet angle of the rotor…

A:

Q: Which choice is correct for the comparison of the operation of impulse and reaction turbines? (a)…

A: Impulse turbines: Impulse turbines are those in which the fluid directly impinges to rotating blades…

Q: A wastewater plant requires inflow of 165 gpm with a pressure head of 10ft. What would you recommend…

A: Given question: A waste water plant requires inflow of 165 gpm with a pressure head of 10 ft.What…

Q: (2) As shown in hydraulic circuit below, the fixed delivery rate of hydraulic pump qp=120 mL/r,…

A: Gggg

Q: A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. At what speed, in RPM,…

A:

Q: Due to surface tension , water from faucet tapers from a diameter of 0.5 in to 0.3 in. after falling…

A: Given that: Water from faucet tapers from a diameter of 0.5 in to 0.3 in. after falling 10 in. It is…

Q: A reservoir discharges into another reservoir via a 3.2 km long pipe that has a pipe diameter of 300…

A: We will use Bernoulli's theorem in this equation let reservoir A be at point 1 and reservoir B be at…

Q: Explain by drawing the shape of a hydroelectric power plant, write down the 3 types of turbines…

A: Hydro electric power plant

Q: Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net…

A: Given, net head, h=65mRPM, N=700rpmshaft power, SP=400KWflow ratio, φ=0.18B1D1=0.1D1D2=0.5hydraulic…

Q: In a large pumped hydro plant, the head from the turbine to the lake surface is 100m. During a…

A: Given : P = 50 MW η=0.7 h = 100 m t = 8 hrs = 28800 s To find : Amount of water pumped

Q: As per common design practice, the three types of hydraulic turbines, in descending order of flow…

A: Given ; Hydraulic turbine is a rotary machine that converts kinetic energy and potential energy of…

Q: A pump rated at 700W is used to transfer water from an open tank at ground level, to another open…

A:

Q: Using data given below, determine the main dimensions and blade angles of a Francis turbine. Net…

A: Given data: The net head is, H=65 m. The speed is, N=700 rpm. The shaft power is, P=400 hp. The…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.