A horizontal underwater plastic meter stick, of mass 446 g and volume 300 cm³, has two additional forces acting on it. There is a downward force of 2 N applied to the left end of the stick and a 6 N force to the right acting on the extreme right end of the stick. [Hint: The buoyant force on a symmetric body of uniform density acts at the geometric center of the body.] Assume g = 10 N/kg. 2 N r? W 6 N

A horizontal underwater plastic meter stick, of mass 446 g and volume 300 cm³, has two additional forces acting on it. There is a downward force of 2 N applied to the left end of the stick and a 6 N force to the right acting on the extreme right end of the stick. [Hint: The buoyant force on a symmetric body of uniform density acts at the geometric center of the body.] Assume g = 10 N/kg. 2 N r? W 6 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

+ Space Trusses Learning Goal: To analyze the forces within space truss members and the reaction forces that act on space trusses. A space truss is a stable three-dimensional structure that consists of members joined at their ends. If the external loading is applied at the joints, and the joints are ball-and-socket connections, the members of a enaro trice may ha traatad ac tun-force membere Figure 0.50 m- 1.50 m 1.50 m 0.50 m B D < 2 of 2 2.00 m F
A block whose dimensions are 8in x 9in x 16in weighs 11lb under the water. It is located 20 in below the surface of the water. Its weight in air should be Select the correct response: O 21.82 kg O 34.32 kg 48.00 kg O 25.56 kg
Recall that muscle generates force at 30 N/cm?. Two cross sections are taken from the rectus femoris muscle (bipennate muscle similar to the diagram below). The length and width of the first cross section is 6 cm and 5 cm respectively with a 35° angle of pennation. The length and width of the second cross section is 5.6 cm and 3 cm respectively with a 31° angle of pennation. What is the predicted maximum tendon force (FTendon) of this muscle in Newtons? Answer to the nearest 0.1 N. Freodas
Pressure is stronger at the bottom of an item immersed in a fluid than at the top. Select the correct response: True False
! SHOW FULL SOLUTION ! *dont copy answer to others *draw FBD *use the GIVEN DATA BELOW PROPERLY *write eligibly thank you!
The system shown in (Eigure 1) is called Russell's traction Figure 57°F 6 1 of 1 > - Part A If the sum of the downward forces exerted at A and B by the patient's leg is 36.2 lb, what is the weight W? Express your answer in pounds to three significant figures. W Submit ΕΘΕΙ ΑΣΦΑΤΗ voc Request Answer Return to Assignment 9 Provide Feedback · C ? <14 of 14 Review
1-F X b Answered: Detern X 3 Google day X 7 Google anxi X 7 https://moodle.nct.edu.om/mod/quiz/attempt.php?attempt=827752&cmid=98802&page=2 earning Portal Courses Reports - e-Services Academic Departments - ETC - CIMS- A brass specimen is subjected to a Tensile test in a laboratory. The following data obtained are: Length of Specimen = 335 mm; Diameter of Specimen = 15 mm; Yield Stress = 1326 MPa; Ultimate Stress = 2496 N/mm²; Solution: The Elongation at 29 kN (in mm) = Load at Yielding (in N)= Fracture Stress = 1763 MPa; % of Elongation = 48 % % of Reduction in area = 37 %. Determine the elongation at 29 kN, Load at yielding, Maximum load, Load at fracture, Final Length & Final diameter. Take Young's Modulus as 106 GPa. Maximum Load (in N)= Fracture Load (in N)= Google dazji X Final Length (in mm)= Final Area (in mm²) = Final Diameter (in mm) = Outcome 1_Classi X Diap O
ENGR 2411 Applied England Environmental Science Spring 2024 Semester The University of Oklahoma School of Civil Problem 2-(40 pts.) Prerequisite Quiz Statics Page 3 of 4 Your Mind Harper loves to zipline. Every summer they travel the Midwest looking for new line adventures. During they became increasingly concerned abour the tension in the zipline cable recent adve friend take a picture of them while on They had a his line and want you to determine the tension in each of the cables. Look how much fn Harper is having! Cable AB has a length of 150 ft and Cable BC has a length of 195 ft. Harper has a weight of 100 lbs (this is the force from Harper). The angle formed by 0-12° and the angle formed by a 37 Assume that the harness holding your friend is perfectly vertical when the picture was taken. Using this information and the information in the image below determine the tension in cables AB and BC. (hint: Draw a free body diagram to get started) ef Sammy Answer
Newton's Law of cooling states that the rate at which heat is lost by a heated body is proportional to the difference in temperature between the body and the surrounding medium. Match the following statements/phrases with the corresponding item in the drop down box. Choices in the box 1. In accordance with the stated law obove, we have the equation? 2. If a thermometer is taken outdoors where the temperoture is 5 deg C, from a room in which the temperature is 20 deg C and the reading drops 10 deg C in one minute, the working equation is? 3. In the obove problem, separoting the variables and integrating will result to? 4. In the obove problem, how long, in minutes, after its removal from the room will the reading be 6 deg C? 5. In the obove problem, ofter 30 seconds, whot will be the thermometer reading? 5.2 dT(body temp)/dt = k(Temp of medium - 5) dr(body temp)/dt = k(Temp of body - Temp of medium) Temp of body = Cenkt +5 2.5 13.7 dr(body temp)/dt = k(Temp of medium - Temp of body)…
PHYS X PHYS X 印 PHYS X PHYS X POTPHYS X PHYS X E PHYS X E PHYS top/semester2/physics%20for%20engineers/PHYS220_CH15_Lecture%20Notes_Problems%2015 19,15.29 S (D Page view A Read aloud V Draw Problem-15-19: page-475 A 0.500-kg object attached to a spring with a force constant of 8.00 N/m vibrates in simple harmonic motion with an amplitude of 10.0 cm. Calculate the maximum value of its (a) speed, and acceleration. (b) the speed and the acceleration when the object is 6.00 em from the equilibrium position, and (c) the time interval required for the object to move from.r50 to r5 8.O0 cm. Solution:
Learning Goal: To use fundamental geometric and statics methods to determine the state of plane stress at the point on an element of material that is rotated clockwise through an angle from the in- plane stress representation of the point. The state of in-plane stress at a point on an element of material is shown. Let o, the same point that is rotated through an angle of 0-35 45.0 ksi, o, 19.0 ksi, and Ty 12.0 kai. Use this information to represent the state of stress of