A hallow cylindrical steel shaft 1.5m long and has an inner and outer diameters respectively equal to 40 and 60mm. The bar is made of AISI 1006 CD steel Syt = 280Mpa, Sut A factor of safety of 2.5 is specified. Find the maximum permissible torque that can be applied to the shaft. Use the maximum distortion energy theory = 330MPA.

A hallow cylindrical steel shaft 1.5m long and has an inner and outer diameters respectively equal to 40 and 60mm. The bar is made of AISI 1006 CD steel Syt = 280Mpa, Sut A factor of safety of 2.5 is specified. Find the maximum permissible torque that can be applied to the shaft. Use the maximum distortion energy theory = 330MPA.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A pipe with an outside diameter of 55 in. and an inside diameter of 5.067 in. is subjected to an axial force of P,-660 lIb, a horizontal force of P,-1520 lb, and a concentrated torque of T-2770 lb-in, acting in the directions shown. Assume a- 29 in. Section properties for the pipe are A-35936 in2, J-25.1213 in.", and I,-1,-12.5606 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element K T. Answer: psi Ty" psi
The material of a certain transmission shaft uses AISI 1030 HR, its yield strength is 260 MPa, the transmission torque of this shaft is 160 N·m, and it is subjected to a uniform axial tension of 0.5 kN. Please calculate according to the Distortion energy theory. The minimum shaft diameter with a safety factor n of 2.5 (to 2 decimal places).
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A shaft is loaded by a torque of 5 KN-m. The material has a yield point of350 MPa. Find the required diameter using(a) Maximum shear stress theory(b) Maximum distortion energy theoryTake a factor of safety of 2.5.
A winch raises a 60# bucket of paint, as shown. The main shaft of the winch is simply supported by bearings at A and C. The winch uses a 6"diameter pulley (B) and torque is applied at the end of the shaft to pull the cart. Determine the minimum shaft diameter based on the Distortion Energy (Von Mises) criterion using on a yield strength of 50ksi and a design factor of 2.0. 12" winch 18" C A Paint Rope
This engine is used in a hoist. Motor 2.5 kWwith the help of gears with a power of and n = 500 rpm.transmits. If the shear strength of the AB shaft is τa = 160 MPa;a) Find the diameter of AB shaft with 1.4 times safety.b) Find the maximum force F the engine can carry.
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in, is subjected to an axial force of P-850 lb, a horizontal force of Pz 1560 lb, and a concentrated torque of T-2940 lb-in, acting in the directions shown. Assume a 49 in. Section propertles for the pipe are A-2.2514 in.?,J-8.199 in.", and ly 1-4.0995 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element Answer: Oy = psi Txy psi
A hollow shaft subjected to a power torque, attains a maximum shear stress Ts. Given that the strain energy stored/volume is 'S where G is the modulus of rigidity. If the shaft is required to transmit 3,897 3G kW at 113 rpm with uniform torque, the inside diameter of shaft is m. Take Ts = 75 MPa and G = 85 MPа.
A Shaft, as shown in figl's, is Subjected to el bending load of 3N, pure torque of anxial pulling torce of 15KN stressescalculate the stressos at ans B. 13KN SammDia 15KN 1000 N-m 250mm
Let's consider a solid circular shaft subjected to the torque loads as shown Determine the minimum required diameter "D" if the shaft is made of a material having a yielding shear stress Ty = 100 MPa, for a factor of safety FS = 2. The polar moment of inertia of a solid circular cross-section is given by Jr.R¹/2. 300 mm B 600 mm 100 N.m 500 N.m 600 mm 400 N.m