A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C=22 uF. The switching frequency is 500 Hz and the DC input voltage is 180V. The THD of the load current is equal to (consider up to the fifth harmonics): Select one: O a. 8% O b. 12% O c. 6% O d. 4%

A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C=22 uF. The switching frequency is 500 Hz and the DC input voltage is 180V. The THD of the load current is equal to (consider up to the fifth harmonics): Select one: O a. 8% O b. 12% O c. 6% O d. 4%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 3G W-CDMA is also known as a. UMTS b. DECT c. DCS-1800 d. ETACS

A: The correct option along with the explanation is provided in the following section.

Q: The single phase full bridge inverter har a resistive load of R=10 2 and de input volkrge ir 2eoU.…

Q: Give a OBSERVATION and RECOMMENDATION about BCD to 7-Segment Display Common Anode and Cathode

A: BCD to 7-segment Display:- I t is a device which has 4 input lines and 7 output lines. This 7…

Q: se full-bridge inverter has a resistive load of R=5 Ohm and the input dc voltag

Q: Parallel resonant inverters are mostly known for the following features: Select one: O a. None of…

A: To Find:The special feature of the parallel resonant inverter.The switching sequence of the…

Q: The load voltage waveform of a single phase full bridge inverter supplied from 300OV DC voltage…

A: Given information about a single phase full bridge inverter is: DC supply voltage Vs=300 Volt.…

Q: In single pulse modulation of PWM inverters, the pulse width is 120°. For an input voltage of 220 V…

A: It is given that:

Q: One half bridge inverter with bidirectional switches and one full bridge inverter with bidirectional…

A: Step 1:It also makes sense. Since power through a given value of resistor is same. The current…

Q: 17 Three-phase inverter is supplied by voltage 800V and is controlled by sinusoidal PWM with…

A: Given, Vs = 800 Volt, Modulation index = 0.8 To calculate the fundamental component of Ac Voltage.

Q: A single phase full bridge inverter has an RL load with R-8 ohm and L=30 mH, the inverter frequency…

Q: Implemet using diodes the logic gates for OR, NOR, AND , NAND

Q: Single -phase full-bridge inverter has a resistive load of R=5 Ohm and the input dc voltage is 220…

Q: A single phase full bridge inverter has rms value of the fundamental component of output voltage…

Q: What are MCBs? Explain the working also?

A: The application of MCBs is protecting circuits from the following - 1. Overcurrent flowing through…

Q: A single-phase full bridge inverter is fed for a dc source such that fundamental component of output…

A: to find the rms value

Q: Use the following figure to answer the following question: In this circuit (inverter), the…

A: When the firing angle of the rectifier is less than 30o, the expression for the output voltage for…

Q: The load voltage waveform of a single phase fill bridge inverter supplied from 300V DC voltage…

A: Solve the first three sub-parts in a multiple sub-part question, unless the student has asked for…

Q: Q1. The single-phase half-bridge inverter in the figure below is switched on to generate a complete…

Q: A three phase inverter has a Y-connected load. The inverter frequency is fo= 60 Hz and the DC input…

Q: A three phase bridge inverter is fed from a 500 V dc source. The inverter is operated in 180°…

A: Given, A three phase bridge inverter is fed from 500 V dc source. Vdc=500 V Supplying a purely…

Q: A single phase bridge inverter has an RLC load with R= 20 ohms, L = 32 mH and C = 0.115 mF. The…

A: The above question is based on single-phase inverter.

Q: demonstrate how the AND, OR, Inverter, and NAND Integrated Circuits work. Using NI Multisim,…

A: The logic gates AND, OR, NOT and NAND gates need to be realized based on the given conditions for…

Q: The JFET uses a positive drain supply voltage. Select one: A. p-channel B. CMOS C. n-channel D. MDS

A: In this question we need to choose a correct option

Q: In a half bridge inverter, the duty cycle for the transistors will be 0.5 0.1 1.0 0.4

A: In this question we need to find a duty cycle for half bridge inverter.

Q: 3G W-CDMA is also known as a. UMTS b. DECT c. DCS-1800 d. ETACS

A: The correct solution is provided in the following section.

Q: 3G W-CDMA is also known as a. UMTS b. DECT

A: The correct option along with the explanation is provided in the following section.

Q: A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C-22 uF.…

Q: 1. СМP В. 2. INX H. 3. XRA B 4. STAX D 5. LDA 2015H

A: Basic Instruction in 8085 are MOV MVI LDAX LDA LHLD STAX STA CMP XRA.....etc

Q: a- For PLL ICs define: 1- fo 2- fL 3- fc

A: fL: Lock range Lock range is defined as the range of frequency over which pll gets locked with the…

Q: Find the distortion factor, for a single-phase half- wave bridge inverter with dc source Vs = 1 kV.…

A: Given a single phase half wave bridge inverter with DC source, Vs=1 kV

Q: Realize the circuit for 4-bit Binary to Gray converter.

A: In order to convert binary to gray: 1) write the table of binary to gray 2) Draw the k-map for each…

Q: -Calculate and draw the load current for the first two-period interval b-Calculate and draw the…

A: Rectifier: Because nearly every electrical appliance runs on DC (Direct Current), the rectifier…

Q: The load voltage waveform of a single phase full bridge inverter supplied from 300V DC voltage…

Q: In a half bridge inverter with Vs as the supply voltage, the maximum output voltage would be OVs/4…

A: Right Answer option Vs/2

Q: More's law specifies that Select one: O 1. None of these. 2. The clock speed of a VLSI chip will…

Question

A full bridge inverter with RLC load having the following values: R=7.5 Ohms, L=12.5 mH, C=22 uF. The
switching frequency is 500 Hz and the DC input voltage is 180V. The THD of the load current is equal to
(consider up to the fifth harmonics):
Select one:
Oa. 8%
O b. 12%
O c. 6%
d. 4%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the inductance for nth harmonic

VIEW

Step 2: Explain the Impedance formula

VIEW

Step 3: Determine the 1st,3rd harmonic impedance

VIEW

Step 4: Determine the 5th harmonic impedance

VIEW

Step 5: Determine the voltage

VIEW

Step 6: Determine the output peak current

VIEW

Step 7: Apply THD formula

VIEW

Solution

VIEW

Step by step

Solved in 8 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the single-phase, full-bridge inverter controlled by the single PWM control, the frequency of the reference signal determines:
Draw circuit and Explain working of Single-Phase inverter with RL load.
A single-phase full bridge inverter is fed for a dc source such that fundamental component of output voltage is 230 V. The input frequency is 50 Hz. Find the rms value of MOSFET and diode currents if load is RLC: R=2 0, L=19 mH, and C=400 µF.
for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.
Question A single-phase full-bridge inverter has a resistive load of 2.4 0 and a source voltage of 48 V. RMS values of the fundamental voltage and output power are respectively and PA
i =(....)A, Rab = (-...)if R=32 2R %3D (a)し1 (b)2,! (c)2,2,(d)2,15 IA 2 R Answer:
VLSI Wafer Yield Given the defect density D= and chip area A, use Murphy's yield model to estimate the chip yield. Calculate for D=0.5 defects/cm2 D=0.5 defects/cm2 and A=1.5 cm2 A=1.5 cm2.
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
The transistor inverter circuit shown in the figure is desired to be designed so that the Ic saturation current is 8mA. Find the Rb and Rc resistances so that the IB current is 120% of the max IB current. (Note: Max IB current is at saturation Ic.)
Q2) Answer the following [1] The waveform of the voltage obtained after rectification is of a ---nature and therefore contains harmonics. [2] The presence of harmonics causes an increase in the RMS value of the input current of the rectifier, and this causes additional dissipation in the conductors. [3] The performance parameters which measure the quality of the inverter output voltage: a) HF b) THD c) DF d) RF [4] High switching losses occur in a inverter as compared to other inverters a) Three-phase, six-step b) Square wave PWM c) Current source d) 1200-mode voltage source [5] The maximum output voltage obtainable with fully controlled full-wave three-phase rectifier is-- volt.
3G W-CDMA is also known as a. UMTS b. DECT c. DCS-1800 d. ETACS