A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six 20 mm diameter steel bolts on 600 mm diameter bolt circle. Determine the maximum to rque that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 8 0 GPa. Drawing not included in this problem. Is the computed torque safe for the rod connected by the flange in item number 29? Justify yo ur answer by stating your computed data. The allowable shear stress of each rod is 60 MPa and the allowable angle of twist is 4 degrees. The diameter of each rod is 200mm and the length is 6 meters. Use G = 80 GPa. Drawing not i Included in this problem.

A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six 20 mm diameter steel bolts on 600 mm diameter bolt circle. Determine the maximum to rque that can be applied without exceeding the shear stress of 60 MPa for each bolt. Use G = 8 0 GPa. Drawing not included in this problem. Is the computed torque safe for the rod connected by the flange in item number 29? Justify yo ur answer by stating your computed data. The allowable shear stress of each rod is 60 MPa and the allowable angle of twist is 4 degrees. The diameter of each rod is 200mm and the length is 6 meters. Use G = 80 GPa. Drawing not i Included in this problem.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flanged bolt coupling consists of seven steel 20mmϕ bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPa. See figure 13
In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm wide. The allowable stresses are 119 MPafor bearing in the plate material and 54 MPa for shearing of the rivet. Determine the minimum thickness of each plate. (Answer must be in millimeters) Round your answer to 2 decimal places.
A flanged bolt coupling consists of seven steel 20mmo bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPA. See figure 13. * R Figure 13
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
Two plates are connected using three 20-mm-diameter bolts as shown in the figure. If the axial load P is 50 kN determine the shear stress in each bolt. 130 mm 25 mm Your answer: O 53 MPa. O 159 MPa O26.5 MPa O 79.5 MPa O 106 MPa: ooo 25 mm P
PROBLEMS: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced according to the following: Sı = 40mm T = 16mm S2 = 80mm S3 = 50mm S4 = 100mm te = 12mm Determine the force T if the allowable tensile stress is 200 MPa, the allowable bolt shear stress is 120MPa and the allowable plate bearing stress is 120 MPa. 2. A long retaining wall is braced by wood shores set at ang angle of 30° and supported by concrete thrust blocks as shown. The shores are evenly spaced, 3m apart. For analysis purposes, the wall and shores are idealized on the second image. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall I assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the wall is F= 190KN. If each shore has a 150mmx150mm square cross section, what is the compressive stress in the shores? Retaining wall Soil Concrete Shore thrust block 30 30 1,5 m…
the butt joint shown in the figure is connected using five 20mm diameter bolt. If the tension force(P) acting on the memeber is 25 kn, determine the maximum shearing stress developed within among the bolts. show graph tnx
The magnitudes of the three forces applied to the eye bolt are T1 = 100lb, T2 =50lb, and T3=170lb. Replace these forces with a single equivalent force R. Show the result on a sketch of theeye bolt.
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm
the butt joint shown in the figure is connected using five 20mm diameter bolt. If the tension force(P) acting on the memeber is 25 kn, determine the maximum shearing stress developed within among the bolts.
20mm Steel Plates in the figure shown are connected by 9 rivets with 20mm diameter. If the Allowable Shear stress for the rivet is 194 MPa and Allowable stress for bearing on the plate is 234 MPa, what is the maximum load P that can be applied in the connection?
Activity 5: Check for understanding Two A36 angles 100x100x9.5mm in tension is connected to a gusset plate with 22 mm diameter bolts in 25 mm diameter holes as shown in the figure bclow. The service deadload is 135 KN dead load. Use 1.2DL + 1.6 LL 1. Determine the value of service live load P based on tensile yielding in the gross area of the angle. D=0.90 2. Determine the value of service live load P based on tensile fracture in the net area of the angle. Anet = 0.85Ag. 0=0.75 3. Determine the value of service live load P based on bolt shear if the normal shear stress of the bolt is 331.2 MPa. Use 0=0.75 热证