A) Express the following values as vectors: forces at A and B, the displacement vectors OA and OB, and the applied moment. B) What is the total moment of the 600 lb and 25001b forces about O? C) Express the force/couple system shown in the figure 1 with an equivalent system consisting of a moment and a resultant force through 0.

Q: In a turbulent flow in a 0.3 m pipe the centerline velocity is 6 m/s, and that 50 mm from the pipe…

A: Given:Type of flow= TurbulentPipe diameter, d=0.3 mCenterline velocity, umax=6 m/s…

Q: Members AB and BC can each support a maximum compressive force of 750 lb, and members AD, DC, and BD…

A: To find: The greatest load P the truss can support. Given: The maximum compressive force is…

Q: QUESTION 3 Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and…

A: input speed, N1 = 1750 rpm output speed, N2 = 725 rpm linear velocity, v = 4000 ft/min

Q: 2) The 25-lb slender rod has a length of 6 ft. Using a collar of negligible mass, its end A is…

A: The weight of rod, W = mg = 25 lb The length, L = 6 ft The position, r = 3x20.5 The angle = 30…

Q: solve for the reaction forces

A:

Q: = Gear B has an angular acceleration of a b 0.15t² rad/s², where t is in seconds, and an initial…

A: Angular acceleration of gear B→αB=0.15t2  ...............equation1→dωBdt=0.15t2→ωBf-ωBi=0.15t33…

Q: In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation 30 over a…

A:

Q: Freehand sketch a set of front/top/right views

A: According to the given data A 3D object is given We need to draw Three projection view of the object…

Q: Natural gas, with the thermodynamic properties of methane, flows in an underground pipeline of 0.6 m…

A:

Q: 100 mm. Part A Compute the force developed in the hydraulic cylinder IJ due to this loading. Express…

A:

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: Question: An ideal gas mixture that contains (% volume) 21% Hydrogen, 34% Octane, 5% Oxygen and 40%…

A: An Ideal gas mixtre that contains (% volume)   Hydrogen H2= 21 % Oxygen O2=5% Methane CH4=40%…

Q: At a given instant A has the motion shown in (Figure 1). Figure 3 ft 1.5 ft. 1 of 1 VA-3 ft/s aA=6…

A:

Q: In the figure, a solid cylinder of radius 12 cm and mass 14 kg starts from rest and rolls without…

A:

Q: Problem 3. The train on the circular track travels with the constant speed indicated, while the…

A: Given-Information:- vA = -28 ft/s...in diagram the value is 28vB = 65 ft/sspeed rate = 2.3 ft/s2…

Q: Q1 If the atmosphere is 50 km thick, and the atmospheric pressure at sea level is approximately 101…

A: Atmosphere thickness = 50 km = 50000 m. Atmospheric pressure at sea level is approximately = P= 101…

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: Q1: a) Find the vector expression for F on AD, b) Find its projection along AC. 3 m D B DA T=4.2 KN…

A: TAB = 4.2 KN

Q: A solid cylindrical shaft is found to fracture when subjected to a torque of 5 kNm. An identical…

A: Torque applied on the shaft: →T=5 KNm Hence the maximum shear stress will be: →τmax=16TπD3…

Q: Air contained in a piston-cylinder assembly undergoes two processes in series, as shown in the…

A:

Q: Calculate the Reynolds number of a fluid flowing with a mass flowrate of 20 kg/min through a pipe of…

A: Mass flowrate m== 20 kg/min=0.33 kg/s Diameter of the pipe (D) = 25 mm = 0.025 m Viscosity (μ) =…

Q: 3. The radius R of a mushroom cloud generated by a nuclear bomb grows in time. We expect that R is a…

A:

Q: this solution doesnt give the final answer of finding the pressure at point A

A: From follow up to an existing solution of a question, we have following information. Total bend loss…

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: In this problem , the condition of Methane, propane & Hexane are given below.

Q: In a typical fuselage or wing section, the stringers and spars would carry most of the mainly…

A: The stringers and spars  are the axial member in the fuselage and used to resists bending .   As…

Q: The rotor of a gas turbine is turning at a speed of 6,600 rpm when the turbine is turned off. It is…

A:

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: 8.4 m. then moves through Water is stored in a pressurised container at a height HT a horizontal…

A:

Q: An opaque surface with the prescribed spectral, hemispherical reflectivity distribution is subjected…

A:

Q: Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal…

A: Input speed of belt N1=1750rpm, Output speed of belt N2=725rpm,Belt Linear VelocityVb=4000ft/min…

Q: For the system shown in Figure 1, m₁ = 35 kg, m₂ = 20 kg, k₁=1500 and k₂=2000 If the initial…

A: The values are m1=35 kg, m2=20 kg, k1=1500 N/m, k2=2000 N/m. The initial conditions of mass m1 is…

Q: could you please help me calculate theheigth in metres of the fluid at time t= 100s

A: The surface area is As=5 m2. The door length is L=0.8 m. The width of the gate is w=0.9 m. The…

Q: Consider a pressure transducer connected to a pipe through a connecting tube of diameter 3.5 mm and…

A: Givend=3.5mmL=50mmμ=0.001 Pa.St=7sC=25×106 mm3/bar=25×106 mm3/105Pa=250 mm3/Pa

Q: Knowing that each of the shafts AB, BC, and CD consists of a solid circular rod. Knowing that both…

A: we are going to apply the Torsion equation over the shaft.

Q: Two mating 12-pitch gears have 18 external and 48 internal teeth, respectively. Determine the…

A: Module is defined as the ratio of pitch circle diameter to no. of teeth. For two mating gear module…

Q: A fan delivers 400 m3 /min of air at 1 atm and 21 C when rotating at 600 rpm, with a head of 8 cm…

A: The volumetric flow rate of the air, V = 400 m3/min The pressure of the air, P = 1 atm The…

Q: 8. What surface texture (in microinches) is specified for the cylindrical surface with a maximum…

A: As per Bartleby Answering Guidelines we are supposed to give answer for first three sub parts of the…

Q: In the wing section below, an applied torque produces shear flows qi and 911 in the two cells. Note…

A:

Q: I want to know the English translation of "flessione e piegamento" according to the movement theory…

A: This question is based on the concept of movement theory.

Q: A block is positioned on a 40° slope as shown, and a spring is attached to it as shown. The spring…

A:

Q: double check please

A: Draw a Force Body Diagram Of the Crate. Given: Mass of the Crate m=200kg Hence Weight…

Q: Question 2: For a 1-kg ball being pushed by a rod in the vertical path with equation r = 0.50, where…

A: To find: The acceleration of the ball. Given: The equation of vertical path is r=0.5θ. At the…

Q: When y is zero, the springs shown in (Figure 1) sustain a force of 70 lb. Figure wwww k= 40 lb/ft…

A:

Q: Water is stored in a pressurised container at a height HT = 8 m. It then moves through a horizontal…

A:

Q: For the instant represented, link CB is rotating counterclockwise at a constant rate N = 4.4 rad/s…

A: The angular velocity of link CB is ωcb=4.4 rad/s  (counterclockwise)

Q: For a closed section beam with thin walls, which of the following options is best to give the least…

A:

Q: D cord 60° JIN с bbck: W₁ = TBD A Tod: Sassume it's uniform (→ 6 = cent of grav ray) W₁₂₁₂ = 8 16 L…

A: Given: Weight of the rod BC→WBC=8 lb Coefficient of friction→μ=0.40 The free body diagram of the rod…

Q: Describe how you designed a vertically coded control unit.

A: Given question: Describe how you designed a vertically coded control unit.

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A:

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.6 m2Inclination angle of door, θ=25oLength of the door, L=1.1 mWidth of…