a) Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage with current lagging- b) Draw a graph depicting power transfer resulting from voltage and current in (a) during 2 complete 50 H: cycles. (4 c) Draw a graph that shows active and reactive power transfer to the load during 2 complete 50 Hz cycles.

a) Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage with current lagging- b) Draw a graph depicting power transfer resulting from voltage and current in (a) during 2 complete 50 H: cycles. (4 c) Draw a graph that shows active and reactive power transfer to the load during 2 complete 50 Hz cycles.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3P: The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous...

See similar textbooks

Similar questions

The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Section [Section Upload answer sheets Find the following parameters of an ac voltage given by the equation v-100sin370t.Find RMS value,form factor, peak factor, average value and frequency. E Submission
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
Generate a conclusion on this following statements: Determine and analyze the voltage regulation characteristics of the alternator with resistive, capacitive, and inductive loading.
Explain the concept of power quality and the various disturbances that can affect it, such as harmonics and transients.
Analyze the impact of harmonics in power systems and propose mitigation techniques.
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
Define three cases on which real and reactive power flow gets affected. Draw the phasor diagrams of all three cases.
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source