A Drainage system exists in the Farm consists of a Surface Open Drains System and a Subsurface Tile Drains System. The Surface op en drains system consists of:- A Main open drain collects drainage water from all Secondary open drains. Flow rate in Main open drain is 4608000 (m³/day). 6 Secondary open drains. Each Secondary open drain collects drainage water from 4 Branch open drain. A group of Branch open drains. Each Branch op en drain collects drainage water from 20 Lateral open drain. A group of Lateral open drains. Each Lateral Open drain collects drainage water from 50 Tile drain. The Subsurface drains system consists of a group of Tile drains. The following information are available:- Tile drains spacing S=80 (m). Drainage coefficient R= 0.01 (m/day). 1- Find the value of flow rate Q of each of:- Secondary open drain Qs (m3/day) Branch open drain QB (m³/day) Lateral open drain QL (m3/day) Tile drain QTile (m3/day) 2- Find Number of Tile drains in the Farm. 3- Find the Length of each Tile Drain.

A Drainage system exists in the Farm consists of a Surface Open Drains System and a Subsurface Tile Drains System. The Surface op en drains system consists of:- A Main open drain collects drainage water from all Secondary open drains. Flow rate in Main open drain is 4608000 (m³/day). 6 Secondary open drains. Each Secondary open drain collects drainage water from 4 Branch open drain. A group of Branch open drains. Each Branch op en drain collects drainage water from 20 Lateral open drain. A group of Lateral open drains. Each Lateral Open drain collects drainage water from 50 Tile drain. The Subsurface drains system consists of a group of Tile drains. The following information are available:- Tile drains spacing S=80 (m). Drainage coefficient R= 0.01 (m/day). 1- Find the value of flow rate Q of each of:- Secondary open drain Qs (m3/day) Branch open drain QB (m³/day) Lateral open drain QL (m3/day) Tile drain QTile (m3/day) 2- Find Number of Tile drains in the Farm. 3- Find the Length of each Tile Drain.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q5) a - A tile drain caters an area of 25 hectares and has a drainage coefficient of 1.3cm. If the drain flows for five days at the design capacity, determine it's discharge and the quantity of water removed.
Determine the spacing of sewer inlets. Inlets run down the center of a street. The extend of the catchment is 174 ft from the centerline of the pipe. The rainfall intensity is 1.9 in/hour and C = 0.84. Pipes carry 1.3 cfs.
drainage system. KA 2 SA 1 = KB 1' SB 1.5 Find the ratio There are two different areas A and B to be drained by means of closed tile (b²-a²), ΤΑ (b² - 2² ) B = Find the ratio and (QD) A (QD)B If the drains carry 1% of average annual rainfall in 24 hours in both the cases. PA PB 5
Determine the diameter of corrugated field drain required to drain area of (20O *100) m if the drainage rate Q = 3mm/day and slope of field drain 12 cm/km. O 110 mm O 90 mm O 150 mm 82 mm
Task 3 a) Concern has been expressed at the local waste water treatment plant regarding the overflows caused by storm water being passed down the same pipeline. The town area main drain has to deal with a maximum of 100m³/s approximately twice a year and so it is proposed that a single drain pipe capable of taking this volume of water be collected from the main storm drains into a temporary storage reservoir to be channelled into the river. The maximum head available is 22m. The pipe is 2050m long, the Darcey Weisbach figure is 0.011, what is the minimum pipe diameter for this project? b) Looking into the future with mean temperature levels exceeding 2.5°C above pre-industrial levels it is considered that the maximum size of the water drain pipe would increase by 4m³/second every decade. Provide a table of expected maximum drain loads over a period from 2030 to 2130 and plot this on a graph. You are advised to plot the maximum expected rainfall against pipe diameter. c) (i) Explain…
A concrete sewer pipe has a cross-sectional area of flow of 0.11045 m2 and a flow velocity of 3.45 m/s. What is the pipe's flow rate (m3/s to 4 dec.pl.) under these conditions? (Hand writen please and do not copy from Chat Gpt)
Q5: A: Determine the size of the intake structure with 1 unit using the following data: Discharge: 3.5 m³/min, Minimum depth of water in river 4m, Low water level: 243m. Assume necessary data.
5. It is known that the wastewater discharge from a block is 0.03 m3/s. Calculate the diameter and flow velocity of the pipe. Does the calculated flow rate meet the established design criteria? (d/D = 0.7; slope = 0.4%; n = 0.013) d
The water is passed through a steel pipe with a diameter of 23 cm (rough height0.046 mm) out of the reservoir. calculate(a) flow (discharge), (b) enable water flow to completeEntrance of full developmentlength).
Q8. Irrigation Engineering Calculate the size of drain at the outlet Given: Area of drainage system=50000m2 Manning (n)= 0.013 Drainage Tile grade=1 in 400 coefficient=DC=1.1cm
a) Concern has been expressed at the local waste water treatment plant regarding the overflows caused by storm water being passed down the same pipeline. The town area main drain has to deal with a maximum of 100m3/s approximately twice a year and so it is proposed that a single drain pipe capable of taking this volume of water be collected from the main storm drains into a temporary storage reservoir to be channelled into the river.The maximum head available is 22m. The pipe is 2050m long, the Darcey Weisbach figure is 0.011, what is the minimum pipe diameter for this project? b) Looking into the future with mean temperature levels exceeding 2.50C above pre-industrial levels it is considered that the maximum size of the water drain pipe would increase by 4m3/second every decade . Provide a table of expected maximum drain loads over a period from 2030 to 2130 and plot this on a graph. You are advised to plot the maximum expected rainfall against pipe diameter. c)(i) Explain briefly how…
Find the diameter of the sewer pipe to carry runoff discharge (m^3 /sec) at full flow condition for the catchment region of area 100,000 m^2, (C= 0.35). The time of concentration is 15 minutes and (i = 5230 It+30)? assume the flowing velocity is 1 m/sec? * - 0.9 m = 1.4 m = 1.0 m = 1.2 m