A direct factor that directly affects the required right of way necessary to construct the road.
Q: Local roads are always with .land access than mobility. а. less b. equal С. higher O d. none of…
A: (c) higher
Q: A reversed curve with diverging tangent is to be designed to connect to three traversed lines for…
A: Given:- AB=185m BC=122.40m CD=285m azimuth=Due East 242o and 302o Type of pavement=Item 311 Number…
Q: What is the relationship of hierarchy of roads and its distance to property
A: Road categorization is a technique for identifying specific traits of the roads within a road…
Q: Often many possible road desigil dile agreed upon reasonable valye solution.
A: Step 1: Often Many possible road design alternatives are possible, however there is an easily agreed…
Q: To avoid the acquisition of rights of way, freeways and expressways in urban areas have been placed…
A: To avoid the land acquisition for rights of way, freeways and expressways, ramps are made along the…
Q: (a) llustrate with a diagram the transportation infrastructure engineering specialties and…
A: “Since you have asked multiple question, we will solve the first question for you. If you want any…
Q: Abstract detailed about "comparative study on green roads and conventional roads "
A:
Q: A design control that determines the future demand of a highway and can reduce the risk of under or…
A: In addition to their particular setting and character, a highway project also needs to take into…
Q: B- How many classes of highways may be identified in the Figure. listed it according to the No.…
A: The classes of highway in the figure: 1.ARTERIAL STREET/ROAD: The number of street in figure: 1,8…
Q: As a transportation engineer, explain the main factors to be considered while planning a…
A: Brief concept- Planning is done before the actual construction of the highway or the road takes…
Q: The full width of land acquired before finalizing a highway, alignment is 3 points known: Pavement…
A: Given the multiple choice questions we have to choose right answer from given options
Q: B- How many classes of highways may be identified in the Figure. listed it according to the No.…
A: There are total 8 classes of highways as identified in the figure.
Q: what is the classifications of roads based on the national principal?
A: Based on National Principal roads are classified as: National Highways State Highways Major…
Q: Discuss the general principles in the realignment of a highway and explain how the work is carried…
A: The realignment of a highway is required for the following conditions. When improvement in…
Q: Explain with sketches the various factors controlling the alignment of roads.
A: The various factors that control the alignment of roads are explained in the following step.
Q: A section of an old freeway in Salalah City. It is a four-lane freeway. with the following…
A: Question is based on the 4 lane freeway . Lane width, number of lanes and ramp density are given in…
Q: Different types of medians can be used in highways. Select one type and present it by providing a…
A: Medians/ Traffic separators- Median is used as a traffic separator to avoid the collision between…
Q: Identify and describe the safety criteria in highway engineering design. Create Flow Chart
A:
Q: Which among the factors for Geometric Design of Highways should be the top priority for mountainous…
A:
Q: identify a methodology in planning that you would use to address the Unauthorized settlements and…
A: Unauthorized settlement also known as Squattered settlement is a day to day challenge which is faced…
Q: The function of roads is traffic .... movement to hiqher rank roads, access to abutting properties…
A: The function of _________ roads is traffic movement to higher rank roads
Q: The factors influencing highway design include choose one of the following cross section of…
A: Factors that affect the design of highway include the user, vehicle and climatic factors along with…
Q: what are the factors that are of specific importance in the location of scenic routes.
A: Scenic routes- It is a road or path designed to enjoy the natural beauty of any location through a…
Q: Define Highway Engineering? 2. What are the basic physical elements of a highway and describe each…
A: Highways and the component of it are mainly for the connecting people from one place to another by…
Q: Determine the required length of curve to be constructed and the station of the end of the curve…
A: simple curve =2° (100m arc basis) North azimuth= -18°26’34” South azimuth = -47°21’08” We know that,…
Q: raw the figure to illustrate your understanding of the problem (as required). Show complete formulas…
A:
Q: On a proposed highway, the speed limit is 120 km/hr, radius of a horizontal curve on this proposed…
A: Given data, Speed limit V = 120 km/hr Radius of curve R = 250 m Superelevation e = 8% = 0.08 Side…
Q: list and describe a variety of survey that a highway engineer have to undertake before designing of…
A: Before designing or planning of a highway it must be reconnaissance and to collect all the…
Q: A type of intersection that aims to enhance safety and operations without extensive construction or…
A: The decision-making process is based on the adjustment of routes and traffic requirements. Two-stage…
Q: The following statements are true, EXCEPT: * Roadside drains are constructed along the road edge to…
A:
Q: Briefly discuss the factors that are specific importance in the location of scenic route
A: Choosing the site of a new road is a crucial first phase through its construction. Typically the…
Q: Answer the following: 1. Identify the design speed, minimum surface, outside shoulder, and paved…
A:
Q: These are nodes in transportation network where two roads meet to form an at-grade junction
A: The junction where two roads meet at grade or at same level is called intersection. In intersection…
Q: A) Both are one-way roads (B) Both are two-way roads (C) One is two-way road and other is one-way…
A: Given data: Given about conflicts at road junctions.
Q: Describe the factors that significantly influence the location of highways in urban areas.
A: The factors that influence the location of highways in urban areas are : The connection between the…
Q: One of the main differences between freeways and local streets is
A: Freeway is a highway that does not have a toll. It has wide roads for fast-moving traffic and…
Q: How are economics factors in to affecting the alignment of roads?
A: Highway alignment, often known as road alignment, is the process of determining the midline of a…
Q: Calculate the extra widening required for a single lane major district highway having horizontal…
A: 9e
Q: Diverts traffic from any existing roadway whenever the construction operations block the flow of…
A: The question is related to uses of different types of roads
Q: b) The vertical alignments of two roads A and B are to be designed with speeds 60km/hr and 80km/r,…
A: Vertical alignment of a road consist of vertical curves and gradient. Vertical curves - are…
Q: 1. Enumerate the Advantages and Disadvantages of the FOUR TYPES OF ROADS according to surface…
A: Four types of roads based on surface course are:- Earthen roads Gravel roads Bituminous roads…
Q: During peak periods, “Trotro” drivers use the shoulders as travel lanes on the section of the Kasoa…
A:
Q: a highway that has a superelevation. Provide the location (international or local) and if possible…
A: When the driver is passing a curve, the road is often tilted or closed at an angle, making it easier…
Q: A highway crew measures the radius of curvature at a tight corner in a highway as 900 feet. What is…
A: Given that.. Radious (r) = 900ft
Q: Look or research for a highway that has a superelevation. Provide the location(International or…
A: Introduction- The Super-elevation is the banks of a highway around a horizontal curve to allow cars…
Q: what Freeway
A:
Q: A 960-m segment of 5.4-km six lane divided TWLTL multilane highway in a suburban area is at a 1.5%…
A: The given data is shown below: Grade=1.5%Lane width=3mPeak hour volume=3500…
Q: a) A heavily used arterial road in Machakos County passes through a number of villages, causing…
A: Introduction- New routes for the roads should be planned, designed, and construct in a planned way…
Q: A 3.25-mile segment of undivided, four-lane highway is primarily on level terrain. The highway…
A: Level of service: It is a measure of the quality of service which describes operational conditions.…
Q: What makes surveys and studies an important part of the design process of highways?
A: Highways are important p[[art of country and location to connect the two or more cities. Also, use…
A direct factor that directly affects the required right of way necessary to construct the road.
Step by step
Solved in 2 steps
- Using the suitable diagram, sketch the road elements that typical been constructed. RIGHT-OF-WAY (ROW) Shoulder Cre Taveas Medan Embankment Dsh Divided Rural HighwayExplain with sketches the various factors controlling the alignment of roads.What are the possible reasons for making a new road that is connected to both end points of an existing road? ps. not graded
- b) The vertical alignments of two roads A and B are to be design with speeds 60km/hr and 80km/r, respectively. Differentiate between the two roads in terms of the level of applicable design standards and the expected cost of implementation.The following cross-section notes of the road was examined to calculate volumes. The width of the roadway is 12m -12 -3 +6 -6 +24 -9 STA 5+040 -15 -4.5 +6 -8 -6 -30 -12 -6 -7 STA 5+140 a. What is the cross section at STA 5+040? STA 5+140?you are an engineer assigned to select an alignment for the proposed highway to link villages A and B.List the 11 guidelines you will follow for the selection of a technically feasible route
- What type of highway curves does the picture falls under and what are the parameters needed to determine in order to design the best facility for it's specific location?What are the various requirements of an ideal highway alignment?Explain the various types of surveys to be carried out before planning a highway system for a given area.