(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures.

Q: DETERMINE A) REACTIONS AT A & E B) RESULTANT FORCES AT PINS B, C & D (Bx, By ect) 2 B 6.5+ * 6.54…

A: Determine the angle: θ=tan-121=63.435 Taking moment about D:…

Q: Problem 4 A lake with a surface area of 750 acres was monitored over a period of time. During a one-…

A:

Q: Homework: Determine the forces in all members for the truss shown below. 5 KN A 10 KN 3m B E 20 KN…

A:

Q: Draw the shear and moment diagrams for the following beams

A: Given, Shear and Bending Moment diagrams are required here.

Q: Question 7 The total rainfall hyetograph of a storm, which took place over a basin is given below.…

A: Baseflow is constant and is 4 m3/s. Depth of excess rainfall is 8 cm. The rainfall intensities…

Q: Piezometers are to be placed at four separate locations in a soil deposit that serves as the…

A: The flow net problem is given in the above figure.  We have to find out the followings:  Number of…

Q: What is the interior angle at C?

A: Here I have assumed the indication of three angles as α, β and γ at station point C.

Q: A horizontal Venturi flow meter consists of a converging-diverging conduit as indicated in the…

A: The volume flow rate Q of a fluid is defined as the flow rate of fluid through a given…

Q: 6. A differential manometer is attached to a pipe, as shown in figure below. Calculate the pressure…

A:

Q: The number of vehicles arriving at the upstream of a freeway bottleneck (free of queues) is shown in…

A: Interval Upstream arrival rate, vph Queue length 6:00-6:15 4000 0 6:15-6:30 6000 10 6:30-6:45…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: en the following transportation network and the production/attraction data in each zone. - min 3 min…

A:

Q: PILE FOUNDATIONS Example: 32/3 The figure shows the load test results of a 20 m long concrete pile…

A: we have to calculate the ultimate load

Q: 1.. Determine the distance between survey stations R and S, which are separated by a body of water.…

A: We are given Angle R-ST = 67o11'39" Angle T-RS = 33o49'38" We know that sum of angles in a triangle…

Q: A construction project has the following activities with their respective durations and…

A: Here, I have drawn the activity on node diagram with respective duration of completion on the node.

Q: a) Write the mathematical expression for one-dimensional flux for advection and diffusion. Do not…

A: a) Write the mathematical expression for one-dimensional flux for advection and diffusion. Do not…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Truss A truss is a construction made solely of elements with two forces. A construction with…

Q: Situation ili: The concrete pad shown in FIGURE SOM-003 is subjected to uniform loads. L=1m, La= 1.5…

A: Determine  1. Maximum shear force in the slab.  2. Maximum moment in the slab.  3. Location of zero…

Q: The pulley system below is in static equilibrium, where load W3 is 650 N, angle a = 600 and angle 0…

A:

Q: 7-33. Use the conjugate-beam slope at C and the displacement A C method and determine the at B. EI…

A: The slope at one point in the real beam equals the shear at the corresponding point in the conjugate…

Q: What is the azimuth of a line that has a bearing of N35o W

A: The angle measured in clockwise direction from the north is called azimuth. Its value lies in…

Q: One of four monthly-read rain gauges on a catchment area develops a fault in a month when the other…

A: One of four monthly read rain gauges on a catchment area three gauges record 37,43 and 51 mm If the…

Q: (BASE ON 100 M LONG) In m3 1. Void Forms (in m) 2. Grade Beam Forms (in m2) 3. Grade Beam concrete…

A: Void form: depth, h = 150 mm width, b = 250 mm Grade beam: depth, h = 500 mm width, b = 250 mm Grade…

Q: Homework: Determine the forces in all members for the truss shown below. 20 KN B N 10 KN E 5 KN A 3m…

A: Determine the force in each members of the truss.  Let's solve using method of joints.

Q: Determine the force in each of the members located to the left of line FGH for the studio roof truss…

A: The truss with the loading and support conditions is given as To find:- Force in members located…

Q: A watershed with an area of 4.0 ha has a composite runoff coefficient of 0.60, find the peak rate of…

A: Area of watershed = 4 ha Runoff coefficient = 0.60 Time of concentration = 15 min [Use MTO IDF…

Q: PROBLEM 2 Determine the reactions at the supports A and B. The joints C and D are fixed connected. 1…

A:

Q: Design a 5.5-km forcemain (f = 0.012) to transport a flow of 250 L/s from a sewage pump station…

A: Length of Force main = 5.5 km Frictional factor, f=0.012 Flow = 250 L/s Suction level = 25.6 m Inlet…

Q: Calculate the unit cost for a virgin mixture and a mixture containing recycled material (RAP)? What…

A: The cost of virgin mixture:- Aggregate:  $15/ton Asphalt binder: $544/ton Mix design AC content:…

Q: Prob. 1. The two aluminum rods support the vertical force of P-20 KN. Determine the requir diameter…

A: Determine the required diameter for each rod

Q: What are the classification of steel and explain the contain , the characteristics and applications…

A: Steel is an alloy of iron and carbon that has a wide range of applications in various industries,…

Q: Q3 Use moment distribution method to determine final end moments for the frame given below. Also…

A: Given:- EI is constant To find:- Moment at B and C Shear force and bending moment diagram

Q: Situation 5: The given simple beam of length L has overhangs of length x on both ends. On the entire…

A: The given beam is statically determinate beam and can be analyzed using the equations of…

Q: -Determine the member forces for all members in the truss shown using the method of joints. Remember…

A: Consider Moment equilibrium A Gx * 10 = 8*10 + 14*20 Gx = 36 Kip Now on considering horizontal force…

Q: There is a three sided plot of land that you need to define. Based upon your field measurements with…

A: Calculating the closure error is necessary to determine whether the closed traverse meets Ohio's…

Q: Question-fluid. Water is flowing through a pipe of 40cm diameter with friction factor equal to 0.06…

A: Water is flowing through a pipe of 40 cm diameter- d=0.40 m, Friction factor f= 0.06, At a distance…

Q: Q:Find Stresses at: Section A-B & Section D-C

A:

Q: bar shown if the temperature increas supports are unyielding and that the buckling. 4 Aluminum A =…

A:

Q: For the beam and loading shown, determine the reaction at the roller support. Assume that the…

A:

Q: Calculate the effective stress acting at Point X in the soil profile shown below for when: 1.…

A:

Q: 7.6 47°35'00", 126°40'12", 205°17'17", and 275°50'24"

A: By subtracting the azimuth from 360°, we can convert azimuths into bearings. In order to calculate…

Q: 7.5 Convert: *(a) 203°26′48″ to grads, (b) 4.56783 radians to degrees, minutes, and seconds, (c)…

A: The values of angle are in given with different units To determine:- a) Convert 203°26'48'' to grads…

Q: The transverse reinforcement of the beam-column joint is a rectangular closed stirrup, which must…

A:

Q: A horizontal impervious floor of length 20 m is provided with a cutoff of a 4 m depth at its…

A: Length of a horizontal impervious floor, b=20 m Depth of cutoff, d=4 m The head causing the flow,…

Q: 1) A cantilever beam is subjected to a 15 kN/m uniform distributed load over the 6m distance of a…

A: The beam with the loading is given as To find:- Elastic curve of the beam Slope and deflection at…

Q: A traverse line was measured in three sections: 295.85 m at slope 8°45', 149.58 m at slope 4°29' and…

A:

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Determine the force in each members of the truss.  Let's solve using Method of Joints.

Q: Plot the expected effluent bsCOD and VSS concentration for an aerobic lagoon modeled as a chemostat…

A: Reactor volumes between 100 and 2000 m3 (increase by 100 m3 increments) Influent bsCOD = 530 mg/L, Q…

Q: 6 A mat foundation is shown in Figure P9.6. The design considerations are L = 12 m, B = 10 m, D, =…

A: Length of foundation= 12 m  Width of foundation= 10 m  Depth of foundation= 2.2 m

Q: An angular measurement has a precision of 1:287. What is the angular error in MINUTES.  You can use…

A: Precision of  angular measurement is 1 : 287

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.